Elster EK280 Скачать руководство пользователя страница 5

Страница: 5 / 163

EK280

Application Manual

7.5.3

Connection configuration status "StCon" ............................................................................... 118

7.5.4

Status of remote terminal "SDst" ............................................................................................ 119

7.5.5

GSM modem status "StM" ...................................................................................................... 120

7.6

Registration of the GSM receiving level in a flexible archive .......................................................... 120

7.6.1

Connection.............................................................................................................................. 120

7.6.2

Parameterization .................................................................................................................... 120

7.6.3

Evaluation with enSuite .......................................................................................................... 121

8 Data transmission protocols .................................................................................................................. 122

8.1

Modbus ............................................................................................................................................ 122

8.1.1

Standard settings of the Modbus Map .................................................................................... 122

8.1.2

Formats ................................................................................................................................... 123

8.1.3

Value readout via Modbus ...................................................................................................... 123

8.1.4

Value update via Modbus ....................................................................................................... 123

8.1.5

Modbus via RS232 interface .................................................................................................. 124

8.1.6

Modbus via internal modem (Modbus RTU_TCP) ................................................................. 125

8.2

Operating a Modbus Master ............................................................................................................ 127

8.2.1

General parameterization ....................................................................................................... 127

8.2.2

Parameterization of Modbus master tasks ............................................................................. 128

8.2.3

Modbus Master Parameter (Modbus Master Info).................................................................. 128

8.2.4

Modbus parameters which are valid for the entire device ...................................................... 129

8.2.5

Connection parameters .......................................................................................................... 129

8.2.6

Modbus master via the terminal device (RS232 directly, RTU or ASCII format) ................... 129

8.2.7

Modbus master via internal modem (RTU_TCP) ................................................................... 133

8.3

Sending SMS messages ................................................................................................................. 135

8.3.1

Preparation ............................................................................................................................. 135

8.3.2

Parameterization .................................................................................................................... 135

9 Archive ...................................................................................................................................................... 138

9.1

Measurement period archive ........................................................................................................... 138

9.1.1

Archive content ....................................................................................................................... 138

9.1.2

Memory capacity .................................................................................................................... 139

9.1.3

Changing the measurement period ........................................................................................ 139

9.1.4

Values relating to measurement periods ................................................................................ 140

9.1.5

Remainder of the measurement period .................................................................................. 140

9.1.6

Freeze metering period archive .............................................................................................. 140

9.1.7

Delete measurement period archive ...................................................................................... 141

9.2

Daily archive .................................................................................................................................... 141

9.2.1

Archive content ....................................................................................................................... 141

9.2.2

Memory capacity .................................................................................................................... 142

9.2.3

Changing the daily limit .......................................................................................................... 142

9.2.4

Values relating to daily limits .................................................................................................. 142

9.2.5

Time elapsed since the daily limit ........................................................................................... 143

9.2.6

Deleting the daily archive ....................................................................................................... 143

9.3

Monthly archive 1 (Monthly meter readings) ................................................................................... 144

9.3.1

Archive content ....................................................................................................................... 144

9.3.2

Memory capacity .................................................................................................................... 144

9.3.3

Changing the monthly limit (= daily limit) ................................................................................ 144

9.3.4

Values relating to months ....................................................................................................... 145

9.3.5

Delete monthly archive 1 ........................................................................................................ 145

9.4

Monthly archive 2 (Measured values) ............................................................................................. 146

9.4.1

Archive content ....................................................................................................................... 146

9.4.2

Memory capacity .................................................................................................................... 147

9.4.3

Changing the monthly limit (= daily limit) ................................................................................ 147

9.4.4

Values relating to months ....................................................................................................... 147

9.4.5

Delete monthly archive 2 ........................................................................................................ 148

9.5

Manual (Events manual) ................................................................................................................. 148

9.5.1

Archive content ....................................................................................................................... 148

9.5.2

Memory capacity .................................................................................................................... 149

9.5.3

Deleting the manual ................................................................................................................ 149

9.6

Modifications archive (audit trail) ..................................................................................................... 149

9.6.1

Archive content ....................................................................................................................... 149

Содержание EK280




































































































































































Результаты поиска

Содержание EK280

Отзывы:

Elster EK280, Руководство по применению, Страница: 5 / 163

Результаты поиска

Содержание EK280

Отзывы: