manualshive.com logo in svg

Elster EK280, Руководство по применению, Страница: 130 / 163

Поделиться
Скачать
Elster EK280 Скачать руководство пользователя страница 130

EK280 

Application Manual 

128 

 

8.2.2 

Parameterization of Modbus master tasks 

It is established via the Modbus master task list which and how much data shall be read or written. This 
Modbus master task list, just like the standard Modbus table (see Chapter 8.1.1) contains a maximum of 70 
entries (instances).  
There is only one Modbus master task list for the whole device. Various links can be parameterized, which 
due to various events access different parts of the Modbus master task list via the parameterized Modbus 
master info instance. The corresponding part of the Modbus master task list must therefore be parameterized 
for each of these events. Parts of the Modbus master task list can also belong to several connections. 
 
The task list consists of three parameters per instance: 
 

Display 

Designation 

Meaning 

Address 

"x" 

24

 

MBAdr 

MMSAd 

Modbus_Master_AufgList
_ 
MdbStartAdr 

The  Modbus  address  from 
which 

the 

number 

of 

registers  shall  be  read  / 
written 

x:8C5 

All Modbus addresses 
are possible here which 
can be found in the 
standard Modbus table  
(see Chapter 8.1.1) 

MMAR 

Modbus_Master_AufgList
_ 
MdbAnzReg 

Number  of  registers,  from 
which  the  Modbus  address 
shall be read / written 

x:8C6 

 

MMRW 

Modbus_Master_AufgList
_ 
MdbRegRWMode 

RW-Mode 

x:8C7 

0: Read-FC03 
1: Read-FC04 
2: Write-FC06 
3: Write-FC16 

 

Table 7: Parameters of the task list 
 

Push-Mode (Write-FC06 / Write-FC16) 

The Modbus addresses configured in the task list are read in the device. In this case the corresponding LIS 
rights are used. For this reason the lock level is also transferred in the link. It must be noted in this case that 
the lock level cannot be higher than the lock level used for parameterization of the task list.  
The writing of data to the remote object can take place by means of two different function codes (FC). 
FC06: Write Single Register 
FC16: Write Multiple Registers 
 

Pull Mode (Read-FC03 / Read-FC04) 

The Modbus addresses configured in the task list are retrieved in the Modbus slave (retrieval system) and 
written internally. In this case the LIS rights of the respective data are used. For this reason the lock level is 
also transferred in the link. It must be noted in this case that the lock level cannot be higher than the lock 
level used for parameterization of the task list. 

 

The retrieval of data to the remote object can take place by means of two different function codes (FC). 
FC03: Read Holding Register 
FC04: Read Input Register 

 

The data format within which the data in this register is transferred, is parameterized via the Modbus list 
(Chapter 8.1.1). 
 

8.2.3 

Modbus Master Parameter (Modbus Master Info) 

 
The Modbus master info which is to be parameterized is configured separately. The connection parameter 
"connection_protocol info" (LIS address x:D79) refers to the Modbus master info instance (1-8), which should 
be used for the link. Individual Modbus master info can be used for each link. 
 

                                                      
 

24

 "x" = Instance of the task (value range from 1-70) 

Содержание EK280




































































































































































Отзывы:

Нет отзывов