manualshive.com logo in svg

Elster EK280, Руководство по применению, Страница: 137 / 163

Поделиться
Скачать
Elster EK280 Скачать руководство пользователя страница 137

EK280 

Application Manual 

135 

 

8.3 

Sending SMS messages 

If the internal GSM modem is connected (see chapter 7.1) or an external GSM modem respectively an external 
device including a GSM modem is connected to the serial interface, the EK280 is able to send SMS messages 
(Short Message Service of GSM-Providers) at occurrence of defined events. 

 

i 

This function is only available since EK280 software version 2.20.  

 

i 

This function creates costs due to data transmission via SMS. Contact your mobile service 
provider to get a favorable tariff. It is your responsibility to optimize this cost factor. 

 

i 

Due to interference of the radio connection failures may occur in data transmission. 

 

i 

This feature only works with a GSM modem.  

 

8.3.1 

Preparation 

Initial conditions: 

- 

A GSM modem is applied as described in chapter 7. 

- 

Transmission of SMS is available with your SIM card. 

8.3.2 

Parameterization 

 

i 

For parameterization of the EK280 you will require a connection cable for the optical interface as 
well as the enSuite application at least with version 2.4, which can be downloaded for free at 
www.elster.com. 

 

 

You can find the following menu paths in 

enSuite

 at 

 "

Parameterize online

" > "

Parameters

" > "

Interfaces

". 

a) 

Configure message contents 

 

With enSuite change to the sub-menu "

SMS

" > "

Layouts

"  

 

You can choose between free SMS layouts (no. 1 - 10) and pre-defined SMS layouts (no. 11 -15). 
The pre-defined layouts are not changeable and are defined as follows: 

 

Layout 

Definition 

Volume profile  
(11) 

The message contains all values of Vm (volume at measurement conditions) 
copied from the measure period profile of the last 24 hours beginning at last gas 
day start. 

Load profile 
(12) 

The message contains all value changes 

∆Vm (volume at measurement 

conditions) copied from the measure period profile of the last 24 hours beginning 
at last gas day start. 

Alarm 
(13) 

The message contains the information if the EK280 has an active alarm regarding 
pressure measurement, temperature measurement or remaining battery lifetime. 

Archive entry 
(14) 

The message contains the latest entry of the measure period profile. The 
complete profile line will be transmitted. 

Month end value 
(15) 

The message contains the latest values of Vm and Vb 

and their last month‘s 

maximum values at end of measure period and start of gas day. 

Содержание EK280




































































































































































Отзывы:

Нет отзывов