manualshive.com logo in svg

Elster EK280, Руководство по применению, Страница: 68 / 163

Поделиться
Скачать
Elster EK280 Скачать руководство пользователя страница 68

EK280 

Application Manual 

66 

 

i 

Lead the protective earth wire laterally out of the bore (see illustration)! If this is not done, 
the antenna cannot be pushed into the correct position. 

 

 

Fasten the antenna by 
tightening the cable gland (see 
illustration.)  
 
 
 

 

 

i 

While tightening, hold the antenna from the inside against the cable gland. Otherwise the 
antenna will be pushed into the housing during tightening. 

 

 

Loosen the M4x6 pan headed screw with which 
the earthing lead is retained between housing 
cover and housing base. 

 

Reattach the earth lead of the antenna together 
with the earth between housing cover and base at 
the illustrated screw post (see illustration). 

 
 
 
 
 

 

i 

Always fit the earth lead between cover and base exactly as illustrated, as the eye on the 
circuit board side will otherwise interfere with housing closure. 

 

 

CAUTION! 
Equipment damage through incorrect connection of the GSM antenna! 

If the connection of the GSM antenna is not properly made at the GSM / GPRS modem socket, this can 
suffer damage.  

Any mechanical strain induced by the cable must be prevented at all costs. 

 

 

Attach the antenna cable with the aid of the light gray plastic 
cable grip installed at the factory. For this reason the length 
of cable between the outlet of the cable grip and the end of 
the antenna plug should be approx. 62 mm (see picture on 
the right hand side), and the shrunk-on tubing should be 
moved along the antenna cable in such a way that after  
clamping it is placed approximately at the center of the grip. 

 

 

 

 

Connect the GSM antenna cable with the modem. 

 

i 

In particular, make sure that the antenna plug does not lie skew in the bushing and that it is 
not stretched any longer by rotary and pull-off forces respectively. 
There is a risk that the socket could detach from the modem! 

 

i 

The cable grip should be carefully pushed 
upwards during the installation of the antenna 
cable. There is always the risk of permanent 
damage to the cable grip! 

Outlet of the 
cable grip  
to end of 
plug is 
approx. 62 
mm! 

Earthing of cover / base 

Oval headed 

screw 

Earthing of 

aerial 

Содержание EK280




































































































































































Отзывы:

Нет отзывов