manualshive.com logo in svg

Elster EK280, Руководство по применению, Страница: 123 / 163

Поделиться
Скачать
Elster EK280 Скачать руководство пользователя страница 123

EK280 

Application Manual 

121 

 

7.6.3 

Evaluation with enSuite 

If there are receiving problems, archive 15 can be read and displayed with the aid of enSuite. 
To do this, it is first necessary to read the contents of this archive with enSuite. 

 

Set up a connection to EK280. 

 

In the left task area, select the option "

Readout archive

" 

 

Mark the 

Archive 15

 (GSM-Archive int.Modem "Ar.Pi") and select the required period. 

 

Use "

Start readout

" to read out the Archive and allow the enSuite database to take it over. 

Displaying the archive contents: 

 

In enSuite press "

Navigation

" and select the relevant "

Device

, then

"LIS-200", "Archives"

 

and then 

"GSM-Archive int. Modem "Ar.Pi"

 and the requested archive is displayed: 

 

 

 

Evaluation: 

 

Logged on to own network; level is 77% and therefore in the acceptable range: Since the system 
status shows no entries, the device is also externally supplied (no battery operation)  
The level is also relatively constant (no fluctuations or break in of the level) 

 

Modem logged out, although mains power supply is on!  

 

 Call window closed? 

 No connection to the GSM network possible (GSM station 

switched off…)! 

 

Modem logged out, battery powered! The modem was unable to log on, as the external power 
supply failed! 

 

 E.g. Maybe the EK280 is connected to the lighting system by mistake, so the power to the 

EK280 is switched off when the light is switched off.  
  

 

 

 

 

 

 

 

Содержание EK280




































































































































































Отзывы:

Нет отзывов