ECKELMANN Virtus 5 Series Скачать руководство пользователя страница 5

Страница: 5 / 183

Firmware V7.16.x

16.05.2023

5/183

6.12

Battery replacement.............................................................................................................................70

6.13

Firmware Update ..................................................................................................................................72

6.13.1

Performing firmware update ...................................................................................................................73

System centre and SIOX connection / terminal assignment ...........................................................75

7.1

System centre terminal diagram.........................................................................................................75

7.1.1

Terminal assignment of the 230 V AC power supply ..............................................................................76

7.1.2

Terminal assignment of the 230 V AC digital inputs ...............................................................................77

7.1.3

Terminal assignment of the 230 V relay outputs ....................................................................................78

7.1.4

Terminal assignment of the CAN bus terminals .....................................................................................79

7.1.5

Terminal assignment of the SIOX interfaces ..........................................................................................80

7.1.6

Terminal assignment of the COM3 / Modbus terminals (RS485) ...........................................................81

7.1.7

Terminal assignment of communication interfaces ................................................................................82

7.2

SIOX extension module terminal diagram .........................................................................................84

7.2.1

SIOX - Terminal assignment of the interfaces ........................................................................................85

7.2.2

SIOX - Terminal assignment of the 230 V AC relay outputs...................................................................86

7.2.3

SIOX – Terminal assignment of the 230 V AC digital inputs

...................................................................88

7.2.3.1 SIOX - connection of energy, gas, water and event meters ...................................................................90

Operation and access to the system centre ......................................................................................92

Menus of the system centre ................................................................................................................94

9.1

On-site at the device ............................................................................................................................94

9.1.1

Layout of the touch screen .....................................................................................................................94

9.1.1.1 Status bar and quick info........................................................................................................................95

9.1.1.2 Main menu and central controls .............................................................................................................96

9.1.1.3 Navigation and other ..............................................................................................................................99

9.1.2

Login to the system centre (unlocking).................................................................................................100

9.1.2.1 Service mode - suppression of remote alarm signalling ......................................................................102

9.1.3

Remote control of E*LDS components (terminal mode) ......................................................................103

9.1.3.1 Operation in terminal mode ..................................................................................................................104

9.1.4

Specification of the numbering of menus and entry screens ...............................................................106

9.1.5

Overview of the menu tree ...................................................................................................................107

9.1.5.1 Main menu............................................................................................................................................109

9.2

Remote ................................................................................................................................................161

9.2.1

Remote control via Virtus Control Desk (VCD) ....................................................................................162

9.2.2

Remote operation of the system centre using VNC (Virtual Network Computing) ...............................165

Decommissioning and disposal .......................................................................................................167

10.1

Decommissioning / Demounting ......................................................................................................167

10.2

Disposal ..............................................................................................................................................167

System centre alarms and messages ..............................................................................................168

Содержание Virtus 5 Series
























































































































































































Результаты поиска

Содержание Virtus 5 Series

Отзывы:

Похожие инструкции для Virtus 5 Series

Бренды по названию

Популярные бренды

ECKELMANN Virtus 5 Series, Руководство по эксплуатации

Результаты поиска

Содержание Virtus 5 Series

Отзывы:

Похожие инструкции для Virtus 5 Series

Бренды по названию

Популярные бренды