ECKELMANN Virtus 5 Series Скачать руководство пользователя страница 171

Страница: 171 / 183

Firmware V7.16.x

16.05.2023

171/183

•

Firmware update OK

Firmware update performed successfully

---

LSM: Invalid power meter

An invalid power meter has been configured
in the Load Shedding Manager (LSM).

Check configuration in the Load
Shedding Manager (LSM)

Pushover data error

The configuration data for Pushover have
errors.

Please contact Customer Service

Pushover file error

Configuration for Pushover could not be
loaded

Please contact Customer Service

Pushover error: x

An error with the error number x has occurred
during the transmission of messages and
alarms via Pushover.

Please contact Customer Service

Pushover No network

Pushover could not establish a network
connection

Check:

Network configuration (see

Menu 4-1-5

)

Pushover configuration (see

Menu 4-1-7

)

Pushover Keys error

Incorrect user key or incorrect application
token in the Pushover configuration

Check user key and application token in
the Pushover account

Pushover message low.

The quota for Pushover messages is low

Adjust message quota in the Pushover
account

Pushover message limit

The limit for the transmission of messages in
the Pushover account has been reached

Adjust message quota in the Pushover
account

Pushover transmission error

Error in the Pushover alarm transmission

Check:

network configuration (see

Menu 4-1-5

)

Pushover configuration (see

Menu 4-1-7

)

Pushover language definition

Pushover message could not be created

Please contact Customer Service

Pushover timeout

A timeout has occurred during the
transmission of messages and alarms via
Pushover

Check:

network configuration (see

Menu 4-1-5

)

Pushover configuration (see

Menu 4-1-7

)

Reboot ANF_SERVICE

Reboot of the system centre requested via
LDSWin

---

Sum.-Z:Ung.Zaehler

No power data could be determined for at
least one meter in the totaliser module.

Check:

Configuration of the totaliser
(only using LDSWin)

Alarm config loss

Alarm configuration could not be loaded

Please contact Customer Service

Verst. DP M-Bus

Configuration change: M-bus meter data point ---

VNCPort x:y

VNC port x has been changed over to y
x: old VNC port
y: new VNC port

---

W-Stop: Power

Water stop: The limit value for the power has
been exceeded

---

W-Stop: Ung.Sum-Z

Water stop: The configured totaliser is not
valid

Check:

Configuration of the water stop
(only using LDSWin)

W-Stop: Consumption

Water stop: The limit value for the
consumption has been exceeded

---

Содержание Virtus 5 Series
























































































































































































Результаты поиска

Содержание Virtus 5 Series

Отзывы:

Похожие инструкции для Virtus 5 Series

Бренды по названию

Популярные бренды

ECKELMANN Virtus 5 Series, Руководство по эксплуатации

Результаты поиска

Содержание Virtus 5 Series

Отзывы:

Похожие инструкции для Virtus 5 Series

Бренды по названию

Популярные бренды