ECKELMANN Virtus 5 Series Скачать руководство пользователя страница 82

Страница: 82 / 183

Firmware V7.16.x

16.05.2023

82/183

•
•

•

7.1.7 Terminal assignment of communication interfaces

Interfaces at the bottom on the device

Interface

Designation

Type

Function

CAN bus

CAN1 and CAN2
COMBICON terminal
blocks

Connection of the system centre to

the first CAN bus segment via CAN1,
the second CAN bus segment via CAN2 (CAN2 only for VSC 5510 /
VSC 5110).

For details, see chapter

Terminal assignment of the CAN bus terminals.

COM1 /
MODEM

RS232
Sub-Min-D (male)

For connection

of a null modem cable for the connection of the PC software LDSWin
or
of a modem.

For details, see chapter

Configuration of the E*LDS system using Service PC

on-site.

COM2

RS232
Sub-Min-D (male)

M-bus

For details, see chapter

M-bus interface for consumption data capture.

SIOX data cable RJ45 female connector

Data cable for SIOX extension modules

ATTENTION: DO NOT

connect using the Ethernet/LAN network cable!

For details, see chapter

SIOX - connection to the system centre

Interfaces on the left on the device

COM3/
MODBUS

RS485
COMBICON terminal
block

For the connection of UA 30 / Dixell controllers and LDS1 gateways.

For details, see chapter

Terminal assignment of the COM3 / MODBUS

terminals (RS485).

COM4

RS232
Sub-Min-D (male)

For the connection of external controllers (Danfoss AHT / Wurm AHT)

For details, see chapter

Integration of external controllers

ETHERNET/
LAN 2

RJ45 female connector

Ethernet / LAN interface for the connection of a controller of the Virtus LINE,
e.g.

VPC 5000

ETHERNET/
LAN 1

RJ45 female connector

Ethernet / LAN interface for the connection to the Intranet / Internet via VPN
router (PC software LDSWin and for

Remote control via Virtus Control Desk

(VCD)

USB - Host

USB 1.1 female
connector A

For plugging in a USB stick for a firmware update;
for details, see chapter

Firmware Update.

The functions of the communication interfaces are configured in Menu 4-1-5.



Содержание Virtus 5 Series
























































































































































































Результаты поиска

Содержание Virtus 5 Series

Отзывы:

Похожие инструкции для Virtus 5 Series

Бренды по названию

Популярные бренды

ECKELMANN Virtus 5 Series, Руководство по эксплуатации

Результаты поиска

Содержание Virtus 5 Series

Отзывы:

Похожие инструкции для Virtus 5 Series

Бренды по названию

Популярные бренды