E-FLITE Beechcraft Bonanza 15e ARF Скачать руководство пользователя страница 7

Страница: 7 / 60

Beechcraft Bonanza 15e ARF Assembly Manual

□□

Step 18

Use your radio to center the rudder and elevator

servos. Insert the pushrods into the outer hole of the

servo arms from below and secure them with snap

keepers.

□

Step 19

Slide a silicone keeper on to the threaded end of

the rudder and elevator pushrods. Install a clevis on

each of the pushrod ends so that it is approximately

centered on the threads.

Tailcone Installation

Parts Required

Fuselage

Tailcone

Tools Required

Awl

Felt-tipped pen

Manila card stock

Thin CA

Low-tack tape

Pin vise

1/16-inch drill bit

□

Step 1

Cut three tabs measuring 1 x 3/8-inch from Manila

card stock. Use an awl to make a hole 1/8-inch from

the end and centered along the length of each tab.

□

Step 2

Align the holes in the tabs with the pre-drilled holes

in the tailcone mounting tabs on the fuselage and

secure them to the fuselage with low-tack tape.

□

Step 3

Slide the tailcone in place on the fuselage under the

card stock tabs. Tape it to the fuselage with low-tack

tape so that it cannot move.

Содержание Beechcraft Bonanza 15e ARF





























































Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды

E-FLITE Beechcraft Bonanza 15e ARF, Инструкция по сборке

Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды