E-FLITE Beechcraft Bonanza 15e ARF Скачать руководство пользователя страница 24

Страница: 24 / 60

Beechcraft Bonanza 15e ARF Assembly Manual

□□

Step 21

Insert the pushrod into the outer hole of the servo

arm and secure it with a snap keeper. Connect the

clevis to the aileron control horn and secure it with

the silicone keeper.

□

Step 22

Repeat steps 1 through 21 to install the aileron servo

and pushrod in the opposite wing panel.

Flap Servo Installation

Parts Required

Wing panels

Micro servos (2)

Clevises (2)

Snap keepers (2)

Silicone keepers (2) 4-inch steel pushrods (2)

#2 x 3/8-inch wood screws (8)

Flap servo hatches (2)

Servo mounting blocks (4)

6-inch servo extension leads (2)

Tools Required

Pin vise

1/16-inch drill bit

5/64-inch drill bit

#1 Phillips screwdriver

Dental floss

Low-tack tape

Pencil

Ruler

Hobby knife

Thin CA

12-minute epoxy

Mixing sticks

Mixing cups

Felt-tipped pen

Sidecutters

Pliers

Scissors

□□

Step 1

Prepare the flap servos by installing the

grommets and bushings. Note that the bushings are

installed from the bottom of the servo.

□□

Step 2

Use a #1 Phillips screwdriver to remove the small

servo arm and install a standard 4-way arm on each

servo.

□□

Step 3

Use sidecutters to remove three of the servo arms,

leaving one long arm. Note that both the left and

right flap servos have the arms oriented in the same

direction.

Содержание Beechcraft Bonanza 15e ARF





























































Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды

E-FLITE Beechcraft Bonanza 15e ARF, Инструкция по сборке

Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды