E-FLITE Beechcraft Bonanza 15e ARF Скачать руководство пользователя страница 13

Страница: 13 / 60

Beechcraft Bonanza 15e ARF Assembly Manual

□

Step 12

Repeat steps 6 through 11 to locate and install the

elevator servo in the right side of the fuselage.

□□

Step 13

Measure 14 inches from the threaded end of the

ruddervator pushrods and form a 90-degree

bend using pliers.

□□

Step 14

Use sidecutters to trim the bent end of the pushrod

to a length of 1/4-inch.

□□

Step 15

Insert the ruddervator pushrods into the

upper guide tubes by feeding them through the

openings in the top of the firewall.

□□

Step 16

Use your radio to center the ruddervator

servos. Insert the pushrods into the outer hole of the

servo arms and secure them with snap keepers.

□□

Step 17

Slide a silicone keeper on to the threaded end of

each pushrod. Install a clevis on each of the pushrod

ends so that it is approximately centered on the

threads.

Содержание Beechcraft Bonanza 15e ARF





























































Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды

E-FLITE Beechcraft Bonanza 15e ARF, Инструкция по сборке

Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды