E-FLITE Beechcraft Bonanza 15e ARF Скачать руководство пользователя страница 5

Страница: 5 / 60

Beechcraft Bonanza 15e ARF Assembly Manual

□

Step 6

Insert the non-threaded end of the rudder pushrod

into the nylon housing in the fuselage through the

cutout made in step 5.

□□

Step 7

Use a 5/64-inch drill bit in a pin vise to enlarge the

outer hole in the servo arm.

□□

Step 8

Place the servo in the fuselage between the

mounting rails with the output shaft towards the front.

Center the servo fore and aft between the rails. Use

the pushrod to position the servo so that the pushrod

is aligned with the outer hole in the servo arm.

□□

Step 9

Hold the servo in place and use a pencil to mark the

mounting hole locations.

□□

Step 10

Remove the servo and pushrod. Use a 1/16-inch drill

bit in a pin vise to drill the mounting holes.

□□

Step 11

Apply a drop of thin CA to each of the holes to

strengthen the wood. Allow the CA to cure without

using accelerator.

Содержание Beechcraft Bonanza 15e ARF





























































Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды

E-FLITE Beechcraft Bonanza 15e ARF, Инструкция по сборке

Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды