E-FLITE Beechcraft Bonanza 15e ARF Скачать руководство пользователя страница 11

Страница: 11 / 60

Beechcraft Bonanza 15e ARF Assembly Manual

Optional V-Tail Ruddervator Servo

and Pushrod Installation

Parts Required

Fuselage

Micro servos (2)

Clevises (2)

Silicone keepers (2)

Snap keepers (2)

16 1/2-inch steel pushrods (2)

Tools Required

Pin vise

1/16-inch drill bit

5/64-inch drill bit

Pencil

Sidecutters

Pliers

Ruler

Thin CA

#1 Phillips screwdriver

□

Step 1

Remove the canopy by pushing it forward from the

rear edge to disengage the magnets, then lifting and

pulling aft.

□□

Step 4

Use sidecutters to remove three of the servo arms,

leaving one long arm on opposite sides of each

servo.

□

Step 5

Insert the non-threaded ends of the pushrods into

their housings from the rear of the fuselage.

□□

Step 2

Install the grommets and bushings in the rudder and

elevator servos. Note that the bushing is installed

from the bottom of the servo.

□□

Step 3

Use a #1 Phillips screwdriver to remove the small

servo arm and install a standard 4-way arm on each

servo.

Содержание Beechcraft Bonanza 15e ARF





























































Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды

E-FLITE Beechcraft Bonanza 15e ARF, Инструкция по сборке

Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды