E-FLITE Beechcraft Bonanza 15e ARF Скачать руководство пользователя страница 30

Страница: 30 / 60

Beechcraft Bonanza 15e ARF Assembly Manual

□

Step 7

Check that the wing panels are aligned with each

other and apply a binder clamp to the leading edge

tabs to hold the wing halves together.

□

Step 8

Stretch a rubber band between the left and right

wing bolts on the upper and lower surfaces to hold

the wing panels together.

□

Step 9

Check that the wing panels are aligned to each other

and that the panels are pushed together completely.

Clean any excess epoxy off the wing with paper

towels and rubbing alcohol. Stand the wing vertically

while the epoxy cures so that the weight of the

panels doesn’t cause the joint to spread and alter the

dihedral angle.

□

Step 10

Allow the glue to cure completely then remove the

binder clamp, rubber bands and wing bolts.

Main Landing Gear Installation

Parts Required

Wing

Landing gear

#4 x 7/16-inch countersunk wood screws (8)

Tools Required

Pencil

#1 Phillips screwdriver

Pin vise

5/64-inch drill bit

Thin CA

□□

Step 1

With the wing inverted on the work table, place the

main landing gear assembly into the cutout in the

wing. The coil in the strut locates to the aft side, and

the wheel inboard of the strut.

Содержание Beechcraft Bonanza 15e ARF





























































Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды

E-FLITE Beechcraft Bonanza 15e ARF, Инструкция по сборке

Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды