E-FLITE Beechcraft Bonanza 15e ARF Скачать руководство пользователя страница 45

Страница: 45 / 60

Beechcraft Bonanza 15e ARF Assembly Manual

Optional Aluminum Spinner

Installation

Parts Required

Fuselage

Propeller

Cowling

Canopy

1 3/4-inch aluminum spinner

Tools Required

10mm wrench

3/32-inch hex wrench

Note:

There are two sections to the installation. If

you are upgrading to an aluminum spinner from an

already installed plastic spinner, begin at step 5.

Otherwise, perform steps 1 through 4 to install the

aluminum spinner.

□

Step 1

Using the backplate and 5mm collet supplied with

the aluminum spinner, perform steps 1 through 17 on

pages 41 through 44 to locate, mount and trim the

cowling.

□

Step 2

Place the spinner backplate, propeller, washer and

nut onto the collet shaft. Use a 10mm wrench to

tighten the nut.

□

Step 3

Set the spinner cone in place against the backplate

and center the cutouts on the propeller blades.

□

Step 4

Insert the spinner cone retaining bolt and tighten it

with a 3/32-inch hex wrench.

□

Step 5

Remove the plastic spinner, propeller, propeller

adapter and silicone spacer.

Содержание Beechcraft Bonanza 15e ARF





























































Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды

E-FLITE Beechcraft Bonanza 15e ARF, Инструкция по сборке

Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды