E-FLITE Beechcraft Bonanza 15e ARF Скачать руководство пользователя страница 41

Страница: 41 / 60

Beechcraft Bonanza 15e ARF Assembly Manual

□

Step 12

Pull the motor wires from the ESC through the

firewall and connect each wire to its matching

colored wire from the motor.

□

Step 13

Push the connectors and excess wire through the

firewall under the battery tray.

Cowling and Spinner Installation

Parts Required

Fuselage

Canopy

Spinner

Propeller

Silicone keeper

Propeller adapter

Cowling

#2 x 1/4-inch screws (4)

Tools Required

Awl

Manila card stock

Ruler

Low-tack tape

Pin vise

1/16-inch drill bit

Thin CA

Felt-tipped pen

Hobby knife with #11 blade

#1 Phillips screwdriver

Rotary tool with drum sander

□

Step 1

Cut four tabs from Manila card stock that measure

2 1/2 x 1/2-inch each. Use a punch to make a hole

centered along the length and 3/16-inch from the

end of each tab.

□

Step 2

Align two tabs to the top and bottom and flush to

the forward edge of each fuselage side where it

protrudes beyond the firewall. Tape them in place

with low-tack tape.

□

Step 3

Use a 1/16-inch drill bit in a pin vise to drill a 3/8-inch

deep hole in the fuselage at each tab location.

Содержание Beechcraft Bonanza 15e ARF





























































Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды

E-FLITE Beechcraft Bonanza 15e ARF, Инструкция по сборке

Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды