E-FLITE Beechcraft Bonanza 15e ARF Скачать руководство пользователя страница 2

Страница: 2 / 60

Beechcraft Bonanza 15e ARF Assembly Manual

Table of Contents

Table of Contents......................................................2

Introduction................................................................2

Important Warranty Information................................2

Using the Manual......................................................2

Product Registration..................................................2

Contents of Kit/Parts Layout.....................................2

Covering Colors Used...............................................2

Recommended Radio Equipment.............................3

Recommended Setup...............................................3

Optional Equipment...................................................3

Note on Lithium Polymer Batteries............................3

Required Tools and Adhesives..................................3

Rudder and Elevator Servo

and Pushrod Installation........................................4

Tailcone Installation...................................................7

Tail Installation...........................................................8

Optional V-Tail Ruddervator Servo

and Pushrod Installation.....................................11

Optional V-Tail Installation......................................14

Nosewheel Steering Cable and Servo Installation......16

Nose Gear Installation............................................18

Aileron Servo Installation.........................................20

Flap Servo Installation.............................................24

Wing Joining............................................................28

Main Landing Gear Installation................................30

Optional Retract Installation - Nose Gear.................31

Optional Retract Installation - Main Gear.................36

Motor and ESC Installation......................................39

Cowling and Spinner Installation.............................41

Optional Aluminum Spinner Installation..................45

Belly Pan Installation...............................................46

Battery and Receiver Installation.............................47

Optional Cockpit Detail Kit Installation....................48

Final Assembly........................................................50

Radio Connections for Optional V-Tail Installation....51

Radio Connections for Retractable Landing Gear ....52

Control Throws........................................................52

Center of Gravity......................................................53

Preflight..................................................................53

Templates.............................................................55

Warranty Information...............................................57

Disposal of WEEE by

Users in the European Union..............................58

2010 AMA Model Aircraft Safety Code...................59

Introduction

For most private pilots, nothing says “I’ve arrived!”

quite like taking the left seat of a Beechcraft

Bonanza. Considered by many to be the finest

single-engine airplane in general aviation, the

Bonanza is renowned for its classic lines and

sporty-yet-stable flight characteristics. E-flite has

expertly captured the scale lines and satisfying flying

manners of the Bonanza with this 15-size ARF. It

comes out of the box with a great looking UltraCote®

trim scheme and enough scale detail to satisfy any

sport modeler. For those who want to push the scale

looks and performance even further, E-flite offers

several optional accessory kits (sold separately) that

allow you to add cockpit details, electric retracts and

even a V-tail.

Important Warranty Information

Please read our Warranty and Liability Limitations

section on Page 57 before building this product. If

you as the Purchaser or user are not prepared to

accept the liability associated with the use of this

Product, you are advised to return this Product

immediately in new and unused condition to the

place of purchase.

Using the Manual

This manual is divided into sections to help make

assembly easier to understand, and to provide

breaks between each major section. In addition,

check boxes have been placed next to each step

to keep track of its completion. Steps with a single

square (



) are performed once, while steps with

two squares (

 

) indicate that the step will require

repeating, such as for a right or left wing panel, two

servos, etc. Remember to take your time and follow

the directions.

Product Registration

Please register your product online at this address:

www.e-fliterc.com/register

Contents of Kit/Parts Layout

EFL2576

Wing Set

EFL2577

Fuselage

EFL2578

Tail Set

EFL2579

V-tail (optional)

EFL2580

Cowling

EFL2581

Landing Gear Set

EFL2582

Cockpit Kit (optional)

EFL2583

Tailcone

EFL2584

Hardware Pack

EFL2585

Pushrod Set

EFL2586

Belly Pan

Covering Colors Used

White HANU870

Flame Red HANU883

Deep Blue HANU873

Содержание Beechcraft Bonanza 15e ARF





























































Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды

E-FLITE Beechcraft Bonanza 15e ARF, Инструкция по сборке

Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды