E-FLITE Beechcraft Bonanza 15e ARF Скачать руководство пользователя страница 16

Страница: 16 / 60

Beechcraft Bonanza 15e ARF Assembly Manual

Nosewheel Steering Cable and

Servo Installation

Parts Required

Fuselage

Micro servo (1)

Steering cable

Silicone keeper

Pushrod connector and button keeper

17-inch nylon pushrod housing

Tools Required

Pencil

#1 Phillips screwdriver

Canopy glue

3/32-inch drill bit

Pin vise

Thin CA

Pliers

Sidecutters

□

Step 1

Prepare the servo by installing the grommets and

bushings. Note that the bushings install from the

bottom of the servo.

□

Step 2

Use a #1 Phillips screwdriver to remove the small

servo arm and install a standard size 4-way arm on

the servo.

□

Step 3

Use sidecutters to remove three of the servo arms,

leaving one long arm as shown.

□

Step 4

Use a 3/32-inch drill bit in a pin vise to enlarge the

outer hole in the servo arm.

□

Step 5

Insert the pushrod connector in the outer hole in the

servo arm. Use pliers to press the button keeper on

to the bottom of the connector.

Содержание Beechcraft Bonanza 15e ARF





























































Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды

E-FLITE Beechcraft Bonanza 15e ARF, Инструкция по сборке

Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды