E-FLITE Beechcraft Bonanza 15e ARF Скачать руководство пользователя страница 58

Страница: 58 / 60

Beechcraft Bonanza 15e ARF Assembly Manual

Non-Warranty Repairs

Should your repair not be covered by warranty

the repair will be completed and payment will be

required without notification or estimate of the

expense unless the expense exceeds 50% of the

retail purchase cost. By submitting the item for

repair you are agreeing to payment of the repair

without notification. Repair estimates are available

upon request. You must include this request with

your repair. Non-warranty repair estimates will be

billed a minimum of ½ hour of labor. In addition you

will be billed for return freight. Please advise us of

your preferred method of payment. Horizon accepts

money orders and cashiers checks, as well as Visa,

MasterCard, American Express, and Discover cards.

If you choose to pay by credit card, please include

your credit card number and expiration date. Any

repair left unpaid or unclaimed after 90 days will

be considered abandoned and will be disposed of

accordingly. Please note: non-warranty repair is only

available on electronics and model engines.

United States:

Electronics and engines requiring inspection or

repair should be shipped to the following address:

Horizon Service Center

4105 Fieldstone Road

Champaign, Illinois 61822

USA

All other Products requiring warranty inspection or

repair should be shipped to the following address:

Horizon Product Support

4105 Fieldstone Road

Champaign, Illinois 61822

USA

Please call 877-504-0233 or e-mail us at

[email protected] with any

questions or concerns regarding this product or

warranty.

United Kingdom:

Electronics and engines requiring inspection or

repair should be shipped to the following address:

Horizon Hobby UK

Units 1-4 Ployters Rd

Staple Tye

Harlow, Essex

CM18 7NS

United Kingdom

Please call +44 (0) 1279 641 097 or e-mail us at

[email protected] with any questions or

concerns regarding this product or warranty.

Germany:

Electronics and engines requiring inspection or

repairs should be shipped to the following address:

Horizon Technischer Service

Hamburger Strasse 10

25335 Elmshorn

Germany

Please call +49 4121 46199 66 or e-mail us at

[email protected] with any questions or

concerns regarding this product or warranty.

Instructions for Disposal of WEEE by

Users in the European Union

This product must not be disposed of with other

waste. Instead, it is the user’s responsibility to

dispose of their waste equipment by handing it over

to a designated collection point for the recycling

of waste electrical and electronic equipment. The

separate collection and recycling of your waste

equipment at the time of disposal will help to

conserve natural resources and ensure that it is

recycled in a manner that protects human health and

the environment. For more information about where

you can drop off your waste equipment for recycling,

please contact your local city office, your household

waste disposal service or where you purchased the

product.

Содержание Beechcraft Bonanza 15e ARF





























































Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды

E-FLITE Beechcraft Bonanza 15e ARF, Инструкция по сборке

Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды