E-FLITE Beechcraft Bonanza 15e ARF Скачать руководство пользователя страница 6

Страница: 6 / 60

Beechcraft Bonanza 15e ARF Assembly Manual

□□

Step 12

Use a #1 Phillips screwdriver and the screws

provided with the servo to install the rudder servo in

the fuselage.

□

Step 13

Repeat steps 7 through 12 to locate and install the

elevator servo in the right side of the fuselage.

□

Step 14

Use a razor saw to remove the section of frame at

the right rear corner of the fuselage. Make the cuts

flush with the opening in the side.

□□

Step 15

Measure 14 inches from the threaded end of the

rudder and elevator pushrods and form a 90-degree

bend using pliers.

□□

Step 16

Use sidecutters to trim the bent end of the pushrod

to a length of 1/4-inch.

□□

Step 17

Insert the rudder and elevator pushrods into the

lower guide tubes by feeding them through the

openings in the top of the firewall.

Содержание Beechcraft Bonanza 15e ARF





























































Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды

E-FLITE Beechcraft Bonanza 15e ARF, Инструкция по сборке

Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды