E-FLITE Beechcraft Bonanza 15e ARF Скачать руководство пользователя страница 36

Страница: 36 / 60

Beechcraft Bonanza 15e ARF Assembly Manual

Optional Retract Installation

- Main Gear

Parts Required

Wing

2 1/2-inch wheels (2)

Main landing gear retracts (L&R)

#4 x 7/16 countersunk wood screws (8)

Radio

Tools Required

Hobby knife

Sealing iron

Sidecutters

1.5mm hex wrench

2.5mm hex wrench Pencil

File

Threadlock

Ruler

Felt-tipped pen

Pin vise

5/64-inch drill bit

Sealing iron

#1 Phillips screwdriver

Rotary tool with cutoff wheel

□□

Step 1

Use a hobby knife with a #11 blade to cut the

covering over the landing gear wells. Leave

approximately 1/4 inch of covering overhanging the

interior of the gear well.

□□

Step 2

Use a hobby knife to slit the covering approximately

each 1/2 inch and use a sealing iron to seal the

covering to the edges of the wheel well. Trim any

overhanging covering with a hobby knife.

□□

Step 3

Trim the protruding piece of plywood from the rib

next to the gear mounting rails.

□□

Step 4

Use a felt-tipped pen to measure 3 inches from

the base of the retract unit. Cut the gear leg to this

length using a cutoff wheel in a rotary tool.

□□

Step 5

Use a file to make two 1/4 inch long flat spots on the

gear leg, one each on the forward and aft sides.

Содержание Beechcraft Bonanza 15e ARF





























































Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды

E-FLITE Beechcraft Bonanza 15e ARF, Инструкция по сборке

Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды