E-FLITE Beechcraft Bonanza 15e ARF Скачать руководство пользователя страница 39

Страница: 39 / 60

Beechcraft Bonanza 15e ARF Assembly Manual

Motor and ESC Installation

Parts Required

Fuselage

Motor

ESC

#4 steel washers (4)

Nylon spacers (4)

4-40 x 3/4-inch hex screws (4)

Adhesive-backed hook and loop tape

Tools Required

Threadlock

#1 Phillips screwdriver

Tapered reamer

Ruler

Scissors

Pencil

3/32-inch hex wrench

□

Step 1

Apply threadlock to each of the countersunk screws

supplied with the motor mounting hardware to install

the motor mount.

□

Step 2

Use a #1 Phillips screwdriver to install the motor

mount on the back of the motor.

□

Step 3

Locate the #4 steel washers supplied with the motor

hardware. Place a washer on each of the 4-40 x 3/4-

inch motor mounting screws.

□

Step 4

Noting that the motor leads will exit to the right side

of the fuselage, slide a screw and washer into the

top left motor mount hole. Place a nylon spacer over

the exposed screw. Apply a drop of threadlock on the

end of the threads.

□

Step 5

Use a 3/32-inch hex wrench to install the motor on

the firewall with the power leads exiting to the right-

hand side.

Содержание Beechcraft Bonanza 15e ARF





























































Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды

E-FLITE Beechcraft Bonanza 15e ARF, Инструкция по сборке

Результаты поиска

Содержание Beechcraft Bonanza 15e ARF

Отзывы:

Похожие инструкции для Beechcraft Bonanza 15e ARF

Бренды по названию

Популярные бренды