manualshive.com logo in svg

DMP Electronics XTLplusINT Series, Инструкция по установке и программированию

Поделиться
Скачать
DMP Electronics XTLplusINT Series Скачать руководство пользователя страница 21

Digital Monitoring Products

 

XTLplus International Series Installation and Programming Guide

14

Send Communication Trouble

Enable communication fail notification by selecting YES at COMM TRBL. Select NO to 
disable. Default is 

YES

. If set to yes, Comm Troubles will be logged in panel events.

When COMM TRBL is YES and the panel detects a failure of communication, the panel 
sends an S72 (Comm Trouble) message through a backup communication method with 
notification of the failure. If both primary and secondary methods of communication 
fail, then two S72 messages will be sent via the third communication method, if 
programmed. When communication is restored, the panel sends an S73 (Comm 
Restored) message through the primary communication. 
If the primary or secondary communication type is CELL, S72 and S73 messages include 
the cell signal strength as a -dBm value.

First Cell APN

Enter the first APN (Access Point Name). This allows an access point for cellular 
communication and is used to connect to a DNS network. The APN may contain two 
lines of 16 characters to equal 32 characters. Default is set to 

SECURECOM400

.

Receiver 1 Programming

Allows you to set the options for the first receiver the panel attempts to contact when 
sending reports. The XTLplusINT supports communication to two receivers.

Alarm Reports

YES

 enables Abort, Alarm, Alarm Restoral, Alarm Bell Silenced, Ambush, Exit Error, and 

System Recently Armed reports to be sent to this receiver. Default is 

YES

.

Supervisory/Trouble Reports

YES

 enables Supervisory, Trouble, Trouble Restoral, Force Armed, Late to Close, and 

Fault reports to be sent to this receiver. Default is 

YES

.

Opening/Closing and User Reports

YES

 enables Opening/Closing, Code Changes, and Bypass reports by user to be sent to 

this receiver. Default is 

NO

.

Test Report

Enter 

YES 

to enable the Recall Test report to be sent to this receiver.

First IP Address

Enter the first (primary) IP address where the panel sends network or cellular 
information. Enter all 12 digits and leave out the periods. For example, enter IP address 
192.168.0.250 as 192168000250. The periods display automatically.
The message is sent using first Cell APN and the first IP Address. If no acknowledgment 
is received, first Cell APN and the second IP address are used, followed, if needed, by 
second Cell APN and first and second IP addresses, respectively.

First IP Port

Enter the first IP port number to be used in conjunction with the first IP Address. The 
IP port identifies the port used to communicate messages to and from the panel. The 
default IP Port setting is 

2001

.

Second IP Address

Enter the second (secondary) IP address where the panel sends network or cellular 
information. Enter all 12 digits and leave out the periods. For example, enter IP address 
192.168.0.250 as 192168000250. The periods display automatically.

Second IP Port

Enter the second IP port number to be used in conjunction with the second IP address. 
The IP port identifies the port used to communicate messages to and from the panel. 
The default IP Port setting is 

2001

.

TEST TIME

COMM TRBL    NO   

YES

FIRST CELL APN

SECURECOM400

RECEIVER 1 PROG

ALARM            NO   

YES

SPV/TRBL        NO   

YES

O/C USER        NO   

YES

TEST RPT        NO   

YES

FIRST IP ADDR

000.000.000.000

FIRST IP PORT

 

 

     

2001

SECOND IP ADDR

000.000.000.000

SECOND IP PORT

 

 

     

2001

Содержание XTLplusINT Series


























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды