Danfoss VLT Automation Drive FC 360, Руководство по программированию

Страница: 81 / 156

9-16 PCD Read Configuration
Select the parameters to be assigned to PCD 3–10 of the
telegrams. The number of available PCDs depends on the
telegram type. Values in PCD 3 to 10 contain the actual data
values of the selected parameters.
Option: Function:
[1663] Terminal 54 Setting
[1664] Analog Input AI54
[1665] Analog Output 42 [mA]
[1667] Pulse Input 29[Hz]
[1668] Pulse Input 33 [Hz]
[1669] Pulse Output 27 [Hz]
[1670] Pulse Output 29 [Hz]
[1671] Relay Output
[1672] Counter A
[1673] Counter B
[1679] Analog Output AO45
[1684] Comm. Option STW
[1685] FC Port CTW 1
[1690] Alarm Word
[1691] Alarm Word 2
[1692] Warning Word
[1693] Warning Word 2
[1694] Ext. Status Word
[1695] Ext. Status Word 2
[1697] Alarm Word 3
[3421] PCD 1 Read For Application
[3422] PCD 2 Read For Application
[3423] PCD 3 Read For Application
[3424] PCD 4 Read For Application
[3425] PCD 5 Read For Application
[3426] PCD 6 Read For Application
[3427] PCD 7 Read For Application
[3428] PCD 8 Read For Application
[3429] PCD 9 Read For Application
[3430] PCD 10 Read For Application
[3450] Actual Position
[3456] Track Error
9-18 Node Address
Range: Function:
126
*
[ 0 -
126 ] Enter the station address in this parameter or,
alternatively, in the hardware switch. To adjust the
station address in
parameter 9-18 Node Address ,
set the hardware switch to 126 or 127 (that is all
switches set to
on ). Otherwise, this parameter
shows the actual setting of the switch.
9-19 Drive Unit System Number
Range: Function:
1037
*
[0 - 65535 ] Manufacturer specific system ID.
9-22 Telegram Selection
Option: Function:
[1] Standard telegram
1 Select a standard PROFIBUS
telegram configuration for the
frequency converter as an
alternative to using the freely
configurable telegrams in
parameter 9-15 PCD Write Configu-
ration
and parameter 9-16 PCD Read
Configuration .
[100]
*
None
[101] PPO 1
[102] PPO 2
[103] PPO 3
[104] PPO 4
[105] PPO 5
[106] PPO 6
[107] PPO 7
[108] PPO 8
[200] Custom telegram 1
9-23 Parameters for Signals
Option: Function:
[0]
*
[302] Minimum Reference
[303] Maximum Reference
[312] Catch up/slow Down Value
[341] Ramp 1 Ramp Up Time
[342] Ramp 1 Ramp Down Time
[351] Ramp 2 Ramp Up Time
[352] Ramp 2 Ramp Down Time
[380] Jog Ramp Time
[381] Quick Stop Ramp Time
[412] Motor Speed Low Limit [Hz]
[414] Motor Speed High Limit [Hz]
[416] Torque Limit Motor Mode
[417] Torque Limit Generator Mode
[553] Term. 29 High Ref./Feedb. Value
[558] Term. 33 High Ref./Feedb. Value
[590] Digital & Relay Bus Control
[593] Pulse Out 27 Bus Control
[595] Pulse Out 29 Bus Control
[615] Terminal 53 High Ref./Feedb. Value
[625] Terminal 54 High Ref./Feedb. Value
[696] Terminal 42 Output Bus Control
[748] PCD Feed Forward
[890] Bus Jog 1 Speed
[891] Bus Jog 2 Speed
[1500] Operating hours
[1501] Running Hours
[1502] kWh Counter
[1600] Control Word
[1601] Reference [Unit]
[1602] Reference [%]
Parameter Descriptions Programming Guide
MG06C602 Danfoss A/S © 7/2015 All rights reserved. 79
4 4