CTS iCPE Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 145

background image

11

2.2 Navigating CLI

After you successfully access to the Gateway Controller, you will be asked for a login username. Enter
your  authorized  username  and  password,  and  then  you  will  be  directed  to  the  User  Mode.  In  CLI
management,  the  User  Mode  only  provides  users  with  basic  functions  to  operate  the  Gateway
Controller. If you would like to configure advanced features of the Gateway Controller, such as, VLAN,
QoS and Rate limit control, you must enter the Configuration Mode.  The following table provides an
overview of modes available in this Gateway Controller.

Command Mode

Access Method

Prompt Displayed

Exit Method

User Mode

Login username &
password

ICPE>

logout

Privileged Mode

From user mode, enter the

enable

command

ICPE#

disable, exit, logout

Configuration Mode

From the enable mode, enter
the

config

or

configure

command

ICPE(config)#

exit

NOTE:

By default, the model name will be used for the prompt display. For convenience, the

prompt display “ICPE” will be used throughout this user’s manual.

2.2.1 General Commands

This section introduces you some general commands that you can use in all modes, including “help”,
“exit”, “history” and “logout”.

Entering the command…

To do this…

Available Modes

help

Obtain a list of available commands in
the current mode.

User Mode
Privileged Mode
Configuration Mode

exit

Return to the previous mode or login
screen.

User Mode
Privileged Mode
Configuration Mode

history

List all commands that have been
used.

User Mode
Privileged Mode
Configuration Mode

logout

Logout from the CLI or terminate
Telnet session.

User Mode
Privileged Mode

«
...
9
10
11
12
13
...
»

Содержание iCPE


















































































































































Отзывы:

Нет отзывов

Похожие инструкции для iCPE

Бренд: J4C Страницы: 4

Бренд: ABB Страницы: 6

Бренд: Farris Engineering Страницы: 12

Бренд: Eastern Times Technology Страницы: 4

Бренд: Vacon Страницы: 18

Бренд: Falcon Страницы: 3

Бренд: OBaby Страницы: 47

Бренд: ABB Страницы: 63

Бренд: Lawler Страницы: 6

Бренд: Data Aire Страницы: 28

Бренд: RAKwireless Страницы: 6

Бренд: Ziton Страницы: 36

SUPERSTAR E-3000/F2

Бренд: praher Страницы: 10

Бренд: IDEC Страницы: 97

Бренд: V2 Страницы: 13

Бренд: Belkin Страницы: 60

Aqua Wireless 8347

Бренд: claber Страницы: 172

Бренд: RTI Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды