CTS iCPE Скачать руководство пользователя страница 102 | Manualshive

Страница: 102 / 145

background image

102

Heat
Alarm

0x04

Event /Cleared

0x00

- Event identifier for the event
which is no more active.
- If no Event Parameter is
provided, there are no active
events for the specified
Notification Type.

Overheat detected

0x01

Node Location Report (Node
Naming and Location Command
Class)

Overheat detected,
Unknown Location

0x02

Rapid Temperature Rise

0x03

Node Location Report (Node
Naming and Location Command
Class)

Rapid Temperature Rise,
Unknown Location

0x04

Under heat detected

0x05

Node Location Report (Node
Naming and Location Command
Class)

Under heat detected,
Unknown Location

0x06

Unknown Event

0xFE

Notification Type

Event

Event Parameter(s)

Water
Alarm

0x05

Event /Cleared

0x00

- Event identifier for the event
which is no more active.
- If no Event Parameter is
provided, there are no active
events for the specified
Notification Type.

Water Leak detected

0x01

Node Location Report (Node
Naming and Location Command
Class)

Water Leak detected,
Unknown Location

0x02

Water Level Dropped

0x03

Node Location Report (Node
Naming and Location Command
Class)

Water Level Dropped,
Unknown Location

0x04

Replace Water Filter

0x05

Water Flow Alarm

0x06

Water Pressure Alarm

0x07

Unknown Event

0xFE

Notification Type

Event

Event Parameter(s)

Access
Control

0x06

Event /Cleared

0x00

- Event identifier for the event
which is no more active.
- If no Event Parameter is
provided, there are no active
events for the specified
Notification Type.

Manual Lock Operation

0x01

Manual Unlock Operation

0x02

RF Lock Operation

0x03

RF Unlock Operation

0x04

Keypad Lock Operation

0x05

User Code Report (User Code
Command Class V1)

Keypad Unlock Operation

0x06

User Code Report (User Code

«
...
100
101
102
103
104
...
»

Содержание iCPE


















































































































































Отзывы:

Нет отзывов

Похожие инструкции для iCPE

Бренд: Vacon Страницы: 62

Бренд: ABB Страницы: 138

Бренд: ABB Страницы: 116

Relion 615 series

Бренд: ABB Страницы: 136

Smart-MPPT Li Series

Бренд: Y-Solar Страницы: 6

Бренд: ZIMO Страницы: 38

Бренд: FAAC Страницы: 32

xPico 200 Series

Бренд: Lantronix Страницы: 7

Бренд: Lantronix Страницы: 3

Бренд: Lantronix Страницы: 15

Бренд: Samson Страницы: 6

Extinguishing Control Panel BC06-2EXT

Бренд: LST Страницы: 4

Бренд: National Instruments Страницы: 19

Бренд: WANDERS Страницы: 16

Бренд: D+H Страницы: 16

Бренд: CompuPro Страницы: 33

Бренд: VAT Страницы: 94

ZeZu Multi Tandem

Бренд: OBaby Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды