CTS iCPE Скачать руководство пользователя страница 66

Страница: 66 / 145

Click the

“OK”

button to apply the settings.

3.3.7 Trap Configuration

Click the option

Trap Configuration

from the

Network Management

menu and then the following

screen page appears.

Cold Start Trap:

Select

Disabled

Enabled

for the SNMP trap.

Warm Start Trap:

Select

Disabled

Enabled

for the SNMP trap.

Authentication Failure Trap:

Select

Disabled

Enabled

for the SNMP trap.

Port Link Up/Down Trap:

Select

Disabled

Enabled

for the SNMP trap.

Battery Mode Trap:

Select

Disabled

Enabled

for the SNMP trap.

System Power Down Trap:

Select

Disabled

Enabled

for the SNMP trap. This trap will only be

sent to 1

trap destination.

Click the

“OK”

button to apply the settings.

3.3.8 Mal-attempt Log Configuration

Click the option

Mal-attempt Log Configuration

from the

Network Management

menu and then the

following screen page appears.

Содержание iCPE


















































































































































Результаты поиска

Содержание iCPE

Отзывы:

Похожие инструкции для iCPE

Бренды по названию

Популярные бренды

CTS iCPE, Руководство пользователя

Результаты поиска

Содержание iCPE

Отзывы:

Похожие инструкции для iCPE

Бренды по названию

Популярные бренды