CTS iCPE Скачать руководство пользователя страница 31

Страница: 31 / 145

802.1p Remarking command

ICPE(config)# qos remarking
802.1p-map [1-8]

[1-8]

Configure the mapping of 802.1p remarking
mode.

[1-8]:

Select the mapping entry

ICPE(config-802.1p-map-ID)#
active

Enable the mapping entry.

ICPE(config-802.1p-map-ID)#
802.1p [0-7]

[0-7]

Specify the 802.1p value to be remarked.

ICPE(config-802.1p-map-ID)#
priority [0-7]

[0-7]

Specify the 802.1p remarking value.

ICPE(config-802.1p-map-ID)#
exit

Exit the entry.

DSCP Remarking No command

ICPE(config)# no qos remarking
802.1p-map [1-8]

[1-8]

Set the specific entry back to the default
setting.

ICPE(config-802.1p-map-ID)# no
[ active | 802.1p | priority]

[ active |

802.1p |

priority]

Disable the mapping entry, or set 802.1p value
or 802.1p remarking value back to the default
setting.

Show command

ICPE(config-dscp/802.1p-map-ID)# show

Display the mapping configuration of the
specific entry.

Содержание iCPE


















































































































































Результаты поиска

Содержание iCPE

Отзывы:

Похожие инструкции для iCPE

Бренды по названию

Популярные бренды

CTS iCPE, Руководство пользователя

Результаты поиска

Содержание iCPE

Отзывы:

Похожие инструкции для iCPE

Бренды по названию

Популярные бренды