CTS iCPE Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 145

background image

97

3. After the other controller is successfully included, click “Add Node” again.
4. Turn the other controller into “Learn Mode” again.
5. The controller begins to exchange protocol data with the other controller in the same network.

3.8.1.3 Assigning The Controller as an SIS

The controller is included as a Secondary controller by a Primary Controller. If there is no SIS in the
network, the Primary controller may assigns this controller as SIS. In this case, the controller will turn
into a SIS from Secondary role, which takes approximately 110 seconds.

3.8.2 Z-Wave Node Controller

Node ID:

The identification number of each node assigned.

Vendor:

A unique ID identifying the manufacturer of the device.

Product Type:

A unique ID identifying the actual product type.

Product ID:

A unique ID identifying the actual product.

Home ID:

Unique network address of the link layer network.

«
...
95
96
97
98
99
...
»

Содержание iCPE


















































































































































Отзывы:

Нет отзывов

Похожие инструкции для iCPE

Бренд: Ubisys Страницы: 2

Бренд: WAM Страницы: 62

Бренд: walimex Страницы: 7

Бренд: Walchem Страницы: 2

Бренд: Walchem Страницы: 73

Бренд: Walchem Страницы: 126

Бренд: wallas Страницы: 2

Бренд: Trane Страницы: 72

Бренд: Fuji Electric Страницы: 12

Бренд: heat-timer Страницы: 36

WisLink LPWAN RAK5146

Бренд: RAKwireless Страницы: 9

CURTIS DC Series

Бренд: NOCO Genius Страницы: 2

Бренд: TimeTec Security Страницы: 2

Бренд: Xylem Страницы: 2

Бренд: Conel Страницы: 52

Бренд: Revox Страницы: 57

Бренд: Wittenstein Страницы: 52

Бренд: National Instruments Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды