CTS iCPE Скачать руководство пользователя страница 49

Страница: 49 / 145

Command

Parameter

Description

ICPE(config-if-PORT-PORT)#
auto-negotiation

Set the selected interfaces’ to auto-negotiation.
When auto-negotiation is enabled, speed
configuration will be ignored.

No command

ICPE(config-if-PORT-PORT)# no
auto-negotiation

Set auto-negotiation setting to the default
setting.

Set up port description.

Command

Parameter

Description

Switch(config-if-PORT-PORT)#
description [description]

[description]

Type in the description for the port(s), max 35
characters.

No command

Switch(config-if-PORT-PORT)# no
description

Remove the entered description name for the
selected ports.

Set up duplex mode

Command

Parameter

Description

Switch(config-if-PORT-PORT)#
duplex [full]

[full]

Configure port duplex to

full.

No command

Switch(config-if-PORT-PORT)# no
duplex

Set the selected ports’ duplex mode to the
default setting.

Note1 : Auto-negotiation needs to be
disabled before configuring duplex mode.

Enable flow control operation

Command

Parameter

Description

Switch(config-if-PORT-PORT)#
flowcontrol

Enable the selected interfaces’ flow control
function.

No command

Switch(config-if-PORT-PORT)# no
flowcontrol

Set the selected ports’ flow control function to
the default setting.

QoS configuration.

Command

Parameter

Description

Switch(config-if-PORT-PORT)#
qos rate-limit ingress [0

32-

1000000]

32-

1000000]

Configure

ingress

rate limit, set zero or from

32Kbps to 1000Mbps.

Содержание iCPE


















































































































































Результаты поиска

Содержание iCPE

Отзывы:

Похожие инструкции для iCPE

Бренды по названию

Популярные бренды

CTS iCPE, Руководство пользователя

Результаты поиска

Содержание iCPE

Отзывы:

Похожие инструкции для iCPE

Бренды по названию

Популярные бренды