CTS iCPE Скачать руководство пользователя страница 108 | Manualshive

Страница: 108 / 145

background image

108

Gas Alarm

0x12

Event /Cleared

0x00

- Event identifier for the event
which is no more active.
- If no Event Parameter is
provided, there are no active events
for the specified Notification Type.

Combustible Gas Detected

0x01

Node Location Report
(Node Naming and Location
Command Class)

Combustible Gas Detected,
Unknown Location

0x02

Toxic Gas detected

0x03

Node Location Report
(Node Naming and Location
Command Class)

Toxic Gas detected, Unknown
Location

0x04

Gas Alarm Test

0x05

Replacement Required

0x06

Unknown Event

0xFE

Notification Type

Event

Parameter(s)

Request pending
notification
(Notification Get;
pull mode)

0xFF

3.8.2.2 Power Level Settings

This is used to set the power level indicator value, which should be used by the node when transmitting
RF, and the timeout for this power level indicator value before returning the power level defined by the
application.

Power Level:

The power level indicator value to set.

Valid levels are: NormalPower, minus1dBm, minus2dBm, minus3dBm, minus4dBm, minus5dBm,
minus6dBm, minus7dBm, minus8dBm and minus9dBm.

Timeout value is ignored if Power level is set to NormalPower.

«
...
106
107
108
109
110
...
»

Содержание iCPE


















































































































































Отзывы:

Нет отзывов

Похожие инструкции для iCPE

Бренд: ABB Страницы: 2

Бренд: UE Страницы: 4

Бренд: XBOX Страницы: 7

Бренд: T-Verter Страницы: 121

Бренд: Happy Страницы: 10

Бренд: Canarm Страницы: 3

Бренд: Rain Bird Страницы: 20

Бренд: T&D Страницы: 2

Бренд: T&S Страницы: 5

Бренд: Vageo Страницы: 2

Бренд: Vacon Страницы: 6

Бренд: Vacon Страницы: 24

Бренд: Vacon Страницы: 30

Бренд: Vacon Страницы: 81

Бренд: Vacon Страницы: 100

Бренд: Ultraflex Страницы: 7

Бренд: Casambi Страницы: 2

Бренд: Fuji Electric Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды