CTS iCPE Скачать руководство пользователя страница 50

Страница: 50 / 145

Switch(config-if-PORT-PORT)#
qos rate-limit egress [0

32-

1000000]

32-

1000000]

Configure

egress

rate limit, set zero or from

32Kbps to 1000Mbps.

Switch(config-if-PORT-PORT)#
qos user-priority [0-7]

[0-7]

Port default 802.1p bit. Specify desired port
default 802.1p bit between 0 and 7.

No command

Switch(config-if-PORT-PORT)# no
qos rate-limit ingress

Undo

ingress

rate limit.

Switch(config-if-PORT-PORT)# no
qos rate-limit egress

Undo

egress

rate limit.

Switch(config-if-PORT-PORT)# no
user-priority

Undo User-priority.

Shutdown interface.

Command

Parameter

Description

Switch(config-if-PORT-PORT)#
shutdown

Administratively disable the selected ports’
status.

No command

Switch(config-if-PORT-PORT)# no
shutdown

Administratively enable the selected ports’
status.

Speed configuration.

Command

Parameter

Description

Switch(config-if-PORT-PORT)#
speed [1000 |100 | 10]

[1000 |100 |

10]

Set up the selected interfaces’ speed. Speed
configuration only works when “no auto-
negotiation” command is issued.

No command

Switch(config-if-PORT-PORT)# no speed

Set the selected ports’ speed to the default
setting.

VLAN configuration.

Command

Parameter

Description

Switch(config-if-PORT-PORT)#
vlan dot1q-vlan access-vlan [1-
4094]

[1-4094]

Configure port PVID.

Switch(config-if-PORT-PORT)#
vlan dot1q-vlan mode access

Configure port as dot-1q access port.

Switch(config-if-PORT-PORT)#
vlan dot1q-vlan mode trunk

Configure port as dot-1q trunk port.

Switch(config-if-PORT-PORT)#
vlan dot1q-vlan mode trunk native

Configure port as dot-1q trunk native port.

Switch(config-if-PORT-PORT)#
vlan dot1q-vlan trunk-vlan [1-4094]

[1-4094]

Configure port VID.

Switch(config-if-PORT-PORT)#

[name]

Join port to specific port-based VLAN group.

Содержание iCPE


















































































































































Результаты поиска

Содержание iCPE

Отзывы:

Похожие инструкции для iCPE

Бренды по названию

Популярные бренды

CTS iCPE, Руководство пользователя

Результаты поиска

Содержание iCPE

Отзывы:

Похожие инструкции для iCPE

Бренды по названию

Популярные бренды