CTS iCPE Скачать руководство пользователя страница 125

Страница: 125 / 145

125

Start-up-config:

Back up the data same as last saved data.

Device Configuration to Local File:

Click

Backup

and

define the route where you intend to save data.

Restore:

Click

Browse

, select the designated data and then click

Restore

3.9.2 Z-Wave Upgrade

The Gateway Controller has both built-in TFTP and FTP clients. Users may save or restore their
configuration on-line. Select

Upgrade

from the

Z-Wave Config & Status

menu and then the

following screen page appears.

Protocol:

Select the preferred protocol, either FTP or TFTP.

Config Type:

Choose “Running-config” or “Start-up-config” which the config file will be saved or

restored to

Running-config:

Back up the data you’re processing

Start-up-config:

Back up the data same as last saved data.

User Name:

Enter the specific username to access the File Server.

Password:

Enter the specific password to access the File Server.

Содержание iCPE


















































































































































Результаты поиска

Содержание iCPE

Отзывы:

Похожие инструкции для iCPE

Бренды по названию

Популярные бренды

CTS iCPE, Руководство пользователя

Результаты поиска

Содержание iCPE

Отзывы:

Похожие инструкции для iCPE

Бренды по названию

Популярные бренды