CTS iCPE Скачать руководство пользователя страница 104 | Manualshive

Страница: 104 / 145

background image

104

Access
Control

0x06

Barrier Sensor Not Detected/
Supervisory Error

0x49

(1 byte)
0x00 = Sensor not defined
0x01-0xFE = Sensor ID

Barrier Sensor Low Battery
Warning

0x4A

(1 byte)
0x00 = Sensor not defined
0x01-0xFE = Sensor ID

Barrier detected short in Wall
Station wires

0x4B

Barrier associated with non-Z-
wave remote control

0x4C

Unknown Event

0xFE

Notification Type

Event

Event Parameter(s)

Home
Security

0x07

Event /Cleared

0x00

- Event identifier for the event
which is no more active.
- If no Event Parameter is
provided, there are no active
events for the specified
Notification Type.

Intrusion

0x01

Node Location Report (Node
Naming and Location Command
Class, version 1)

Intrusion,
Unknown Location

0x02

Tampering,
Product covering removed

0x03

Tampering,
Invalid Code

0x04

Glass Breakage

0x05

Node Location Report (Node
Naming and Location Command
Class, version 1)

Glass Breakage,
Unknown Location

0x06

Motion Detection

0x07

Node Location Report (Node
Naming and Location Command
Class, version 1)

Motion Detection,
Unknown Location

0x08

Tampering,
Product Moved

0x09

Unknown Event

0xFE

Notification Type

Event

Parameter(s)

Power
Management

0x08

Event /Cleared

0x00

- Event identifier for the event
which is no more active.
- If no Event Parameter is
provided, there are no active
events for the specified
Notification Type.

Power has been applied

0x01

AC mains disconnected

0x02

AC mains re-connected

0x03

Surge detected

0x04

Voltage Drop/Drift

0x05

Over-current detected

0x06

Over-voltage detected

0x07

Over-load detected

0x08

«
...
102
103
104
105
106
...
»

Содержание iCPE


















































































































































Отзывы:

Нет отзывов

Похожие инструкции для iCPE

Бренд: Ubisys Страницы: 2

Бренд: NEC Страницы: 149

Бренд: NEC Страницы: 13

Бренд: Manfrotto Страницы: 16

Бренд: Bang & Olufsen Страницы: 80

Бренд: Bang & Olufsen Страницы: 13

Бренд: Magellan Страницы: 44

Бренд: Namron Страницы: 3

Бренд: National Instruments Страницы: 17

Бренд: Davey Страницы: 12

Бренд: IN-COMMAND Страницы: 47

Бренд: SYCLOPE Страницы: 60

Бренд: Alde Страницы: 36

YQPV-HP360V/100A

Бренд: PSC Solar Страницы: 22

Бренд: Ezodo Страницы: 7

Бренд: Harman Страницы: 2

Бренд: Linear Technology Страницы: 6

Бренд: Nortek Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды