CTS iCPE Скачать руководство пользователя страница 123

Страница: 123 / 145

123

the FURNACE set point.

DRY

Dehumidification - The system will cycle cooling in relation to the room and
the DRY set point temperature in order to remove moisture from ambient.

MOIST

Humidification - Moist Air, heating or cooling will be activated according to
the MOIST set point.

AUTO

CHANGEOVER

Auto Changeover - heating or cooling will be activated according to the
AUTO CHANGEOVER set point.

ENERGY HEAT

Energy Saving Heating (usually lower than normal set point) - heating will
be activated according to the ENERGY HEAT set point.

ENERGY COOL

Energy Saving Cooling (usually higher than normal set point) - cooling will
be activated according to the ENERGY COOL set point.

AWAY

Away mode, e.g. preventing water from freezing in forced water systems -
heating or cooling will be activated when temperature exceeds the AWAY
HEAT and/or AWAY COOL set points.

FULL POWER

SPEED UP / FULL POWER heating or cooling mode will be activated when
temperature exceeds FULL POWER set point.

Click “SET” to apply settings.

3.8.2.15 Configuration Settings

This is used to allow product specific configuration parameters to be changed.

Parameter Number:

Specify the actual configuration parameter. Valid value is 1~255.

Value:

This box carries the value to be automatically assigned by Parameter Number.

The example of value is shown below:

Raw value

(hex)

Signed 8 bit

representation

(decimal)

Raw value

(hex)

Signed 16 bit

representation

(decimal)

Raw value

(hex)

Signed 32 bit

representation

(decimal)

0x7F

127

0x7FFF

32767

0x7FFFFFFF

2147483647

0x02

0x0002

0x00000002

0x01

0x0001

0x00000001

0x00

0x0000

0x00000000

0xFF

-1

0xFFFF

-1

0xFFFFFFFF

-1

0xFE

-2

0xFFFE

-2

0xFFFFFFFE

-2

0x80

-128

0x8000

-32768

0x80000000

-2147483648

Default:

This is used to specify if the default value is to be restored for all configuration parameters.

Check the box to have the default factory settings must be restored for all Parameter Numbers. If the

Содержание iCPE


















































































































































Результаты поиска

Содержание iCPE

Отзывы:

Похожие инструкции для iCPE

Бренды по названию

Популярные бренды

CTS iCPE, Руководство пользователя

Результаты поиска

Содержание iCPE

Отзывы:

Похожие инструкции для iCPE

Бренды по названию

Популярные бренды