8 of 130
The vender will support the following Domestic MDB
coin changers:
All available NRI MDB
All available Currenza MDB
All available Mars MDB
All available Conlux MDB
All available Coinco MDB
The vender will support the following Domestic MDB
Bill validators:
All available Cashcode MDB
All available Currenza MDB
All available Mars MDB
All available Conlux MDB
All available Coinco MDB
The vender will support Domestic MDB card readers.
SETTING THE TEMPERATURE CONTROL
This vender is equipped with an electronic
temperature sensor. Defrost is controlled both
electronically based on run time of the compressor
and with a manual Defrost thermostat. The temp
sensor is factory pre-set to maintain a cabinet
temperature of 37º Fahrenheit (2.7ºC). It is also a
good practice to ensure the proper operating
temperature prior to installing the vender on location.
To set the temperature, apply power to the vender
and allow it to run for several hours with the glass
door closed or until the minimum cabinet temperature
is achieved. Then, using the method below, verify the
temperature inside the cabinet:
With an electronic temperature sensor, use the
keypad on the service door to show cabinet
temperature in Fahrenheit by pressing the F key
followed by the asterisk (
) key or in Centigrade by
pressing the C key followed by the asterisk key. The
temperature will be shown on the digital display
located on the front of the service door.
The manual Defrost thermostat is located in the
bottom left of the service area. The Defrost control is
preset and is not adjustable.
LOADING THE VENDER
CAN/BOTTLE DRINK TRAYS
The BevMax 6 5800-6/3800-6 Vender does not
require spacers or shims to vend most packages.
Load product in each column one package at a time
insuring that the package being loaded is in front of
the product pusher. Insure that the package is stable
within the column (doesn’t move excessively from side
to side). After loading the vender, test vend each
column to insure proper operation. Please contact a
Service Representative or refer to the proper
Technical Publication for any special settings you may
need.
LOADING CHANGE TUBES
The changer tubes can be loaded using one of the
following methods:
1. Load the coin mechanism with coins to the
desired level by inserting coins in the loading
slots on the coin tube front.
Minimum coin tube levels are:
6-8 nickels
7-8 dimes
5-6 quarters
Note: A low coin level in the coin tubes will
interfere with operation of the bill validator.
2. For exact cash accountability and to insure
maximum dollar bill acceptance, load the
mechanism utilizing the coin insert slot on the
front of the vender while in the coin TUBE
FILL/DISPENSE mode in the test menu in the
programming section of Technical Manual for
more information.
For additional information about coin mechanism,
refer to the manufacturer’s instructions.
POWER AC DISTRIBUTION BOX
The power distribution box is where the 120VAC or
220VAC input voltage is broken down to the main
operating voltages of the vender (24 VAC and 12
VAC) by a transformer. Those voltages are sent to
the controller via the P1 (3 pin) connector. Domestic
Venders contain a 15 Amp Outlet which provides
power to the Refrigeration Unit. It contains a main
power switch/plug that allows power to the AC
Distribution Box to distribute AC power to the lights,
evaporator fan, and refrigeration system, which are
always energized when the vender is powered up. It
is located inside the service area, mounted to the
back wall.
VENDING MACHINE CONTROLLERS
Atlas Control Board
The Atlas Control Board is located on the inside of the
Service Door. It controls all the logic functions of the
machine. It communicates with its peripherals (I/O
Board, Display Board, Coin Mechanism, Bill Validator,
Card Reader, Etc.) in an MDB format. It has 3 USB
ports, has built in telemetry, CCM connection WLAN
(Zigbee), soft boot, service button, multiple LED’s for
troubleshooting, interfaces with the I/O and LED
boards. Note: USB3 should be used for uploading or
downloading files including firmware updates.
I/O Controller
The I/O Controller is the heart of the Glass Front
Vender and is located on the rear wall inside the
service area. After receiving the message from the
Atlas Control Board to vend a particular selection, it
determines the necessary steps to make that happen
and then executes them. It then advises the Atlas
Control Board of its status. It is SIM Card
Содержание BevMax MEDIA
Страница 1: ...0 of 130 English 80390486 Tier 3 ...