6 of 130
TO OPEN THE ELECTRONIC DOOR LOCK:
1. Plug the vender into a properly powered
outlet.
2. Hold the key FOB 0 to 3” (76.2 mm) in front of
the Delivery Port Door and press the button
on the key FOB.
Note: The wide end of the FOB should face
the door.
3.
The lock will begin releasing the door. The
display will indicate
OPENED.
After the motor
has stopped running, you can pull the door
open.
TO CLOSE THE ELECTRONIC DOOR LOCK:
CAUTION: DO NOT SLAM THE DOOR CLOSED.
Slamming the door closed can damage the electronic
locking device.
1. Push the door to the cabinet until the lock
motor starts. The display will indicate:
CLOSED
2. Continue to push the door for approximately 2
to 3 seconds after the lock motor starts. The
lock will pull the door closed tightly.
3. When the lock motor stops the door will be
locked. Before leaving the vender, ensure
that the door is locked.
The electronic door lock assembly is supplied by
TriTeq Lock and Security. Crane Merchandising
Systems does not carry parts for the TriTeq Electronic
Door Lock. For parts and assistance, please contact:
TriTeq
701 Gullo
Elk Grove Village, IL 60007
Tel: 847-640-7002
Fax: 847-640-7008
Email: triteqlock.com
MANUAL LOCK
Open the service door on the right side using the key
provided in the coin return cup, or if shipped with a
locking clip, remove the clip and install the lock.
Ensure there is no power to the AC Distribution Box.
On venders with a main power switch on the AC
Distribution Box the switch needs to be in the OFF
position. On venders with a main power quick
disconnect plug on the AC Distribution Box the quick
disconnect plug needs to be unplugged. Check that
all connectors are firmly seated on the control board
and at the various components on the service door
(coin mech, keypad, etc.).
Retrieve the main power plug from the hole in the rear
of the vender and plug the cord in a properly
grounded 120VAC, 15 Amp receptacle (U.S. and
Canada).
Open the service door and apply power to the AC
distribution Box (if equipped with a bill acceptor, the
acceptor should cycle twice). The display on the door
will briefly show the software version in use as
“Software ###.## (ie 74#.#1) followed by the default
idle message “ENJOY A REFRESHING DRINK”, the
fluorescent lamp should be lit and the cooling unit
should start. If the display shows “OUT OF
SERVICE”, or the cooling unit fails to start, refer to the
TROUBLESHOOTING SECTION beginning on page
101.
SERVICE NOTE
Battery Backup
The battery backup is used to maintain the date and
time in case of power interruptions, or any time the
main power is off. When the vender is shipped, the
battery is connected and memory is being maintained.
If the vender is to be stored for long periods of time,
disconnecting the battery is recommended. The
following steps will guide you through this procedure.
•
Open the service door, turn the main power
switch to the off position or unplug the main
power harness located on the front of the
power box.
•
Locate the control board mounted on the rear
wall.
•
Remove the battery from its holder (B1).
PLACING THE VENDER ON LOCATION
!! CAUTION !!
DO NOT TRANSPORT THE
VENDER TO OR FROM THE
LOCATION LOADED WITH
PRODUCT OR DAMAGE TO THE
VENDER MAY RESULT.
The vender is intended for
INDOOR USE ONLY.
Indoor Use Only
is defined as inside a structure
constructed with four walls and a roof, and sufficiently
protected from ambient conditions and not subjected
to the effects of weathering. The vender should be
kept out of direct sunlight and away from any heat
source. Do not use this vender in an environment
where flammable or explosive vapors are present.
This machine is not suitable for installation in an area
where a water jet or hose and nozzle may be used.
The vender must be on a solid, flat and level surface.
Ensure the flooring can bear the weight load of a fully
loaded vender (approximately
1109
lbs. or 413kg).
The vender must be positioned close enough to an
electrical outlet so that an extension cord is not
required. If the machine will be subject to user misuse
or vandalism, it is recommended that the vender be
secured to the floor or wall as described in Crane
Merchandising Systems / Dixie-Narco Technical
Bulletin 344. Due to the large size and weight of the
Vender, never attempt to move the Vender with a
Содержание BevMax MEDIA
Страница 1: ...0 of 130 English 80390486 Tier 3 ...
