Coriant 8600 Скачать руководство пользователя страница 52

Страница: 52 / 55

6 Technical Speci

cations

Management protocols

CLI, FTP, SNMP (read), proprietary BMP.
Con

guration Change Noti

cations (CCN).

Other

CPU load gauge.
Memory utilization gauge.
NPU usage gauge.

6.2

LU1 Technical Speci

cations

LU1 Technical Speci

cations

Dimensions

61 x 335 x 387,5 mm (w x h x d)
2.40 x 13.18 x 15.25 in (w x h x d)

Weight

4.4 kg/9.7 lbs without Pluggable Transceivers

Power consumption

Typical 190 W
Maximum 220W

Switch/routing engine

NPU

Packet buffer size

2 GBytes

Max IPv4 entries

440 K

Max number of IPv4 VPN entries

440 K

Interfaces

— One 100GBASE-R CFP2 interface
— Twenty four 1000BASE-X/10GBASE—R
SFP/SFP+ interfaces.
See chapter Pluggable Transceivers in

8600 Smart

Routers Hardware Installation Guide

Synchronization

Synchronous Ethernet support at both ingress and
egress:
— Optical egress signal synchronized to ETSI
SEC or ANSI Stratum 3 (NE clock)
— Optical ingress signal used as reference for
Timing Modules on the CUs

MTU

Max. 9500 byte frames

VLANs

Max. 4096

MAC

lter

Erroneous frames; Short and too long frames;
Flow control and over

Loopbacks

Line loop

Power supply

Nominal -48 Vdc

Card LEDs

Green, yellow and red

6.3

SU1 Technical Speci

cations

SU1 Technical Speci

cations

Dimensions

57 x 151 x 388.45 mm (w x h x d)
2.24 x 5.94 x 15.29 in (w x h x d)

Weight

3.2 kg/7.05 lbs without Pluggable Transceivers

Power consumption

Typical 100 W
Maximum 120W

8600 Smart Routers

76.8670-40128B

8665 Smart Router FP7.0 Reference Manual

Содержание 8600
























































Результаты поиска

Содержание 8600

Отзывы:

Coriant 8600, Справочное руководство, Страница: 52 / 55

Результаты поиска

Содержание 8600

Отзывы: