manualshive.com logo in svg

Coriant 8600, Справочное руководство, Страница: 38 / 55

Поделиться
Скачать
Coriant 8600 Скачать руководство пользователя страница 38

2 Line Unit (LU1)

RJ-45 Female Alarm Connector Pin Map

Pin

Signal Name

8
6
7

General Out (NC)
General Out (NO)
General Out (Com)

1

Input1

2

Input2

3

Input3

4

Input4

5

GND

2.6

LU1 LEDs

2.6.1

LU1 Status LEDs

There are four LEDs to indicate the LU1 status and one for the power OK status.

LED Name

Color

States

Local Alarm

RED

ON

when NE itself has a fault.

BLINKING

during the following operations:

1) Manually set to forced blinking.
2) If also yellow LED is blinking, the card/NE has reached
shutdown state after "esw-shutdown" command and can be
removed from NE or power can be switched off.

OFF

otherwise.

Remote Alarm

YELLOW

ON

when online and NE detects or suspects a fault in another

NE or remote site.

BLINKING

during the following operations:

1) Boot-up sequence.
2) Inventory create.
3) Inventory (backup) restoration.
4) Manually set to forced blinking.
5) If also red LED is blinking, the card/NE has reached
shutdown state after "esw-shutdown" command and can be
removed from NE or power can be switched off.

OFF

otherwise.

OnLine

GREEN

ON

when NE is online (it is “up” meaning successful boot-up

sequence

fi

nished and startup permission granted). Note that

online NE may still contain errors.

BLINKING

when CU is active.

OFF

otherwise.

Power

GREEN

ON

when NE power is ON and undervoltage not detected.

BLINKING

Power supply failure.

OFF

otherwise.

2.6.2

LU1 Ethernet LEDs

There are two LEDs to indicate the LU1 Ethernet port status.

8600 Smart Routers

76.8670-40128B

8665 Smart Router FP7.0 Reference Manual

© 2015 Coriant.

38

Содержание 8600
























































Отзывы:

Нет отзывов