Coriant 8600 Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 55

Coriant 8600 Скачать руководство пользователя страница 28

1 8665 Smart Router Overview

1.5.2

Line Unit Redundancy

Ethernet Link Protection (ELP) or [IEEE 802.1AX] Ethernet Link Aggregation (LAG) are applied
for protecting Ethernet physical interfaces. For more information see

8600 Smart Routers Ethernet

Con

fi

guration Guide

.

1.5.3

Switch Unit Redundancy

8665 Smart Router provides two slots for the switch units. With one switch unit the network element
is not redundant in terms of traf

fi

c switching. With two switch units the network element is fully

redundant on the data and control plane switching. Also traf

fi

c is load shared to both switch units to

enhance the QoS behavior and reduce switchover time in case of failure.

1.5.4

Redundancy Terminology

The following terminology is used in connection with redundancy.

Static terms:

•

Working

refers to the card with the higher slot number.

•

Protecting

refers to the card with the lower slot number.

Dynamic terms:

•

Active

refers to the card or interface actually doing its task.

•

Passive

refers to the card or interface that is not currently in performance.

8600 Smart Routers

76.8670-40128B

8665 Smart Router FP7.0 Reference Manual

© 2015 Coriant.

28

«
...
26
27
28
29
30
...
»

Содержание 8600
























































Отзывы:

Нет отзывов