Coriant 8600 Скачать руководство пользователя страница 39 | Manualshive

Страница: 39 / 55

Coriant 8600 Скачать руководство пользователя страница 39

2 Line Unit (LU1)

LED Name

Color

States

Online

GREEN

ON

when administrative status for Ethernet interface is online.

BLINKING

when manually set to forced blinking.

OFF

when administrative status for Ethernet interface is

shutdown or Ethernet link is down.

Link/Activity

GREEN

ON

when Ethernet link is up.

BLINKING

when Ethernet link is up and there is transmit

or receive activity.

OFF

when Ethernet link is down or in shutdown state.

2.7

Cabling

Cabling depends on the SFP, SFP+ or CFP2 type on the optical interfaces, see chapter Pluggable
Transceivers in

8600 Smart Routers Hardware Installation Guide

.

2.8

Laser Safety

See more on laser safety in chapter Pluggable Transceivers in

8600 Smart Routers Hardware

Installation Guide

.

Laser safety

[IEC60825-1, A1, A2]
[IEC60825-2]

Check that the operational temperature range of the SFP/SFP+/CFP2 module is suitable for
the installation environment. Note that the temperature of the SFP/SFP+/CFP2 case can be
approximately 15 degrees higher than the ambient temperature. For more information on the
allowed SFP/SFP+/CFP2 case temperature range see chapter Pluggable Transceivers in

8600

Smart Routers Hardware Installation Guide

.

2.9

LU1 Cooling

It is important to ensure that adequate cooling is used when an LU1 is installed in a subrack. LU1
has temperature sensors that monitor the unit temperatures during operation. LU1 can endure a
single fan failure but if two or all the fans of one fan module fail, the LU1 located above it will go to

power-save

mode after 6 minutes.

The high temperature warning will be raised when the card is operated in high ambient temperature.
This occurs at 45° C/+113° F ambient. Another reason why this warning can be active is if
the air

fl

ow is decreased, which can be caused by a dirty air

fi

lter in the subrack. There are also

critical temperature limits which will cause the cards to go to power-save mode if they are exceeded.

All empty line unit slots have to be shielded with blank cover plates.

76.8670-40128B

8600 Smart Routers

© 2015 Coriant.

8665 Smart Router FP7.0 Reference Manual

39

«
...
37
38
39
40
41
...
»

Содержание 8600
























































Отзывы:

Нет отзывов