Coriant 8600 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 55

Coriant 8600 Скачать руководство пользователя страница 10

About This Manual

About This Manual

This section discusses the objectives and intended audience of this manual,

8665 Smart Router

Reference Manual

and consists of the following sections:

• Objectives

• Audience

• 8600 Smart Routers Technical Documentation

• Document Conventions

• Documentation Feedback

Objectives

The goal is to describe the network element features of 8665 Smart Router.

Audience

This manual is intended for system specialists and personnel involved in network planning.

8600 Smart Routers Technical Documentation

The document numbering scheme consists of the document ID, indicated by numbers, and the
document revision, indicated by a letter. The references in the Related Documentation table below
are generic and include only the document ID. To make sure the references point to the latest
available document versions, please refer to the relevant product document program on the Tellabs
and Coriant Portal by navigating to

www.portal.tellabs.com

> Product Documentation & Software

> Data Networking > 8600 Smart Routers > Technical Documentation.

Document Title

Description

8600 Smart Routers
ATM and TDM Con

fi

guration Guide

(76.8600-50110)

Provides an overview of 8600 NEs PWE3 applications,
including types, Single-Segment and Multi-Segment; PWE3
Redundancy; ATM applications, including PWE3 tunnelling,
Traf

fi

c Management, Fault Management OAM, protection and

TDM applications as well as instructions on how to con

fi

gure

them with CLI.

8600 Smart Routers
Boot and Mini-Applications
Embedded Software Release Notes
(76.8600-50108)

Provides information related to the boot and mini-applications
software of 8605 Smart Router, 8607 Smart Router, 8609
Smart Router, 8611 Smart Router, 8620 Smart Router, 8630
Smart Router and 8660 Smart Router as well as the installation
instructions.

8600 Smart Routers
CLI Commands Manual
(76.8600-50117)

Provides commands available to con

fi

gure, monitor and maintain

8600 system with CLI.

8600 Smart Routers

76.8670-40128B

8665 Smart Router FP7.0 Reference Manual

© 2015 Coriant.

10

«
...
8
9
10
11
12
...
»

Содержание 8600
























































Отзывы:

Нет отзывов