Coriant 8600 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 55

Coriant 8600 Скачать руководство пользователя страница 34

2 Line Unit (LU1)

• Memory access (DRAMs, FLASH memories)

• Performance of high speed data links with other cards

LU1 has a watchdog to reset itself in case of a fatal failure in the CPU subsystem.

2.4

Interfaces

LU1 provides two different interface con

fi

gurations:

• 1x100GBASE-R (CFP2) + 14x1000BASE-X/10GBASE-R (SFP+/SFP)

• 24x1000BASE-X/10GBASE-R (SFP+/SFP)

There are three virtual modules M0, M1 and M2 on LU1. The virtual M0 comprises the
1x100GBASE-R interface, M1 comprises the 10x1000BASE-X/10GBASE–R interfaces and M2
comprises the 14x1000BASE-X/10GBASE-R interfaces. M2 is always available, but M0 or M1
cannot be enabled at the same time.

When selecting between the 1G/10G modes it has to be done in pairs, i.e. M1/0 and M1/1,
M1/2 and M1/3 etc.

For M2/4...13 ports the maximum link span with 10GBASE-ZR SFP+ optics is ~65km depending
on the link conditions, all other 10GBASE-R ports support the full link span.

Fig. 6 LU1 Virtual Modules and Ports

8600 Smart Routers

76.8670-40128B

8665 Smart Router FP7.0 Reference Manual

© 2015 Coriant.

34

«
...
32
33
34
35
36
...
»

Содержание 8600
























































Отзывы:

Нет отзывов