manualshive.com logo in svg

Coriant 8600, Справочное руководство, Страница: 44 / 55

Поделиться
Скачать
Coriant 8600 Скачать руководство пользователя страница 44

3 Switch Unit (SU1)

LED Name

Color

States

Alarm

RED

ON

when SU1 itself has a fault.

BLINKING

during the following operations:

1) Manually set to forced blinking.
2) If also yellow LED is blinking, the card/NE has reached
shutdown state after "esw-shutdown" command and can be
removed from NE or power can be switched off.

OFF

otherwise.

Alarm

YELLOW

ON

when online and SU1 detects some non-critical fault.

BLINKING

during the following operations:

1) Boot-up sequence.
2) Inventory create.
3) Inventory (backup) restoration.
4) Manually set to forced blinking.
5) If also red LED is blinking, the card/NE has reached
shutdown state after "esw-shutdown" command and can be
removed from NE or power can be switched off.

OFF

otherwise.

OnLine

GREEN

ON

when SU1 is online (it is “up” meaning successful boot-up

sequence

fi

nished and and the switch matrix is switching).

Note that online NE may still contain errors.

BLINKING

when manually set to forced blinking.

OFF

otherwise.

Power

GREEN

ON

when NE power is ON and undervoltage not detected.

BLINKING

Power supply failure.

OFF

otherwise.

8600 Smart Routers

76.8670-40128B

8665 Smart Router FP7.0 Reference Manual

© 2015 Coriant.

44

Содержание 8600
























































Отзывы:

Нет отзывов