Coriant 8600 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 55

Coriant 8600 Скачать руководство пользователя страница 15

Safety Notes

Safety Notes

This chapter lists safety notes and their translations for 8600 network elements.

Intended Purpose

The equipment shall be used only for its intended purpose.

Das Gerät soll nur für den vorgesehen Einsatzzweck verwendet werden.

CAUTION: Do not insert an RJ-11 (telephone) plug into Ethernet or E1/T1 ports. Equipment
damage may result.
ACHTUNG: Stecken Sie keine RJ-11 (Telefon) Stecker in die Ethernet oder E1/T1 Anschlüsse
da dieses zu einer Beschädigung des Gerätes führen kann.

CAUTION: Do not climb on or stand on the 8600 network element. Neither the network element
nor its enclosure is designed to support the weight of a person.
ACHTUNG: Steigen Sie oder stellen Sie sich nicht auf das 8600 Netzwerk Element. Weder
des Netzwerk Element noch das Gehäuse sind dafür ausgelegt worden das Gewicht einer
Person zu tragen.

Class 1 Laser Product

Class 1 laser product.
Laserprodukt der Klasse 1.

WARNING: No other types of lasers can be used than supplied and approved by Coriant. If
other types are used, the laser class and compliance to laser safety and EMC standards
must be checked.
WARNUNG: Verwenden Sie keine anderen als die von Coriant gelieferten und zugelassenen
Lasertypen. Falls Sie andere Typen verwenden, müssen die Laserklasse und die Einhaltung
von Lasersicherheits- und EMV-Normen geprüft werden.

76.8670-40128B

8600 Smart Routers

© 2015 Coriant.

8665 Smart Router FP7.0 Reference Manual

15

«
...
13
14
15
16
17
...
»

Содержание 8600
























































Отзывы:

Нет отзывов