Coriant 8600 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 55

Coriant 8600 Скачать руководство пользователя страница 4

Document Information

I2C

Bidirectional two-wire serial bus that provides a communication link between
integrated circuits (ICs).

IEEE

Institute of Electrical and Electronics Engineers

IP

Internet Protocol

IRB

Integrated Routing and Bridging

IS-IS

Intermediate System to Intermediate System (Interior Gateway Protocol)

I-TEMP

Industrial Temperature Range

ITU-T

International Telecommunication Union - Telecom Standardization Sector

LDP

Label Distribution Protocol

LED

Light-Emitting Diode

LER

Label Edge Router

Line card

The line card in the 8600 system consists of an Ethernet Line Card (ELC1), Interface
Module Concentrator (IFC) and up to two Interface Modules (IFMs) (used in 8630
Smart Router and 8660 Smart Router). In 8000 Intelligent Network Manager and
CLI referred to as unit.

Line unit

The line unit in the 8665 Smart Router is the basic building block for the element.
One line unit contains always the traf

fi

c functionality (LU) and, optionally control

functionality (CU).

LU

Traf

fi

c functionality (used in 8615 Smart Router and 8665 Smart Router).

LU1

Line Unit in 8665 Smart Router.

LSP

Label Switched Path

LSR

Label Switch Router

LTE

Long Term Evolution

MAC

Media Access Control Sublayer of Data Link Layer

MP-BGP

Multiprotocol Border Gateway Protocol

MPLS

Multiprotocol Label Switching

MTU

Maximum Transfer/Transmission Unit

NE

Network Element

NEBS

Network Equipment Building Systems

NRTL

Nationally Recognized Testing Laboratory

OAM

Operation, Administration and Maintenance

OSPF

Open Shortest Path First

OSS

Operating Support System

PCML

Pseudo Current Mode Logic

PFC

Power Factor Correction Circuit

PHY

Physical Layer Device

PIM

Power Input Module

PLL

Phase Locked Loop

PPP

Point-to-Point Protocol

8600 Smart Routers

76.8670-40128B

8665 Smart Router FP7.0 Reference Manual

© 2015 Coriant.

4

«
...
2
3
4
5
6
...
»

Содержание 8600
























































Отзывы:

Нет отзывов