Coriant 8600 Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 55

Coriant 8600 Скачать руководство пользователя страница 51

6 Technical Speci

fi

cations

Ethernet functionality

Virtual LAN (VLAN) interfaces.
MAC switching [IEEE802.1D], [IEEE802.1Q].
Virtual Switching Instances (VSI).
[IEEE 802.1ag]/ITU-T [Y.1731] Ethernet OAM connectivity check,
loobpack, and link trace.
ITU-T [Y.1731] Ethernet OAM delay, delay variation, and loss
measurements.
Ethernet line and equipment loops.
[IEEE 802.1AX] Ethernet link aggregation (LAG).
Stacked VLANs (Q-in-Q) in PWE3 applications.
Ethernet over MLPPP in PWE3 applications.
VLAN cross-connections.
VPLS and H-VPLS [RFC4762].

Synchronization

ITU-T [G.8262].
ITU-T [G.813] option 1.
Telcordia [GR-1244] Stratum 3.
Station clock input and output interfaces (SCI/SCO).
Synchronous Ethernet.
[G.8264] SSM over Ethernet.

Link Layer technologies

Ethernet, VLAN.

Quality of service functionality

DiffServ, DiffServ aware MPLS Traf

fi

c Engineering [RFC3270],

[RFC3564] and [RFC5462].
L-LSP and E-LSP supported for MPLS.
7 queues for QoS classes (cs7/StrictPriority1, EF/StrictPriority2, 4
AF classes, Best Effort) per port for IP, MPLS, and Ethernet traf

fi

c.

Traf

fi

c classi

fi

cation can be done based on protocol, source and

destination address, source and destination port and Type of Service

fi

eld.

Policing with Two Rate Three Color Marker [RFC2698].
Queue based WRED for congestion control, SP/WFQ scheduling.
Optional traf

fi

c shaping per traf

fi

c class, VLAN or Ethernet port.

VLAN shaping.

Resiliency

Common logic 1+1 protection, hot-swappable plug-ins.
1:1 RSVP-TE LSP protection.
Fast Reroute [RFC4090], one-to-one and facility backup modes.
Ethernet Link Protection (ELP).
[IEEE 802.1AX] Ethernet link aggregation (LAG).
Dynamic LSP rerouting.
VRRP [RFC3768].
OSPF Graceful Restart [RFC3623], Graceful Restart mechanism for
BGP with MPLS [RFC4781] and LDP Graceful Restart [RFC3478]
mechanisms.
Restart signaling for Intermediate System to Intermediate System
(IS-IS) [RFC3847].
Pseudowire redundancy [draft-ietf-pwe3-redundancy].

Connectivity veri

fi

cation

IPv4 ping and traceroute.
LSP ping and traceroute for RSVP-TE and LDP LSPs [RFC4379].
Single-hop BFD [RFC5880].
VCCV BFD [RFC 5085].
VCCV LSP ping and traceroute [RFC5085].
MPLS OAM [Y.1711].
Packet Loop Tester (PLT).
[IEEE802.1ag]/ITU-T [Y.1731] Ethernet OAM connectivity check,
loobpack, and link trace.
ITU-T [Y.1731] Ethernet OAM delay, delay variation, and loss
measurements.

76.8670-40128B

8600 Smart Routers

© 2015 Coriant.

8665 Smart Router FP7.0 Reference Manual

51

«
...
49
50
51
52
53
...
»

Содержание 8600
























































Отзывы:

Нет отзывов