Control Techniques Unidrive HS30 Скачать руководство пользователя страница 28

Страница: 28 / 66

Unidrive M300/HS30 Quick Start Guide

Issue Number: 7

Brake Controller
Post-brake Release
Delay

0.0 to 25.0 s

1.0 s

RW Num

Brake Controller
Initial Direction

rEF (0), For (1), rEv (2)

rEF (0)

Txt

Brake Controller
Brake Apply Through
Zero Threshold

0.00 to 25.00 Hz

1.00 Hz

RW Num

Brake Controller
Enable

diS (0), rELAy (1), dig IO (2),

USEr (3)

diS (0)

Txt

Trip 0

0 to 255

Txt

ND NC PT PS

Trip 1

0 to 255

Txt

ND NC PT PS

Trip 2

0 to 255

Txt

ND NC PT PS

OUP Enable

Stop (0) or Run (1)

Run (1)

Txt

OUP Status

-2147483648 to 2147483647

RO Num ND NC PT

Frequency Controller
Proportional Gain
Kp1

0.000 to

200.000 s/rad

0.100 s/rad

RW Num

Frequency Controller
Integral Gain Ki1

0.00 to

655.35 s

/rad

0.10 s

/rad

RW Num

Sensorless Mode
Filter

4 (0), 5 (1), 6 (2),

8 (3), 12 (4),

20 (5) ms

4 (0) ms

Txt

Spin Start Boost

0.0 to 10.0

1.0

RW Num

PID1 Output

±100.00 %

RO Num ND NC PT

PID1 Proportional
Gain

0.000 to 4.000

1.000

RW Num

PID1 Integral Gain

0.000 to 4.000

0.500

RW Num

PID1 Feedback
Invert

Off (0) or On (1)

Off (0)

Bit

PID1 Output Upper
Limit

0.00 to 100.00 %

100.00 %

RW Num

PID1 Output Lower
Limit

±100.00 %

-100.00 %

RW Num

Action on Trip
Detection

0 to 31

RW Num ND NC PT US

Maximum Heavy
Duty Current Rating

0.00 to Drive HD Current Rating A

RO Num ND NC PT

Software Version

0 to 99.99.99

RO Num ND NC PT

User Drive Mode

OPEn.LP (1), RFC-A (2)

OPEn.LP (1)

RFC-A (2)

Txt

ND NC PT US

Reference Selected

-Pr

to Pr

or Pr

to Pr

RO Num ND NC PT

Pre-ramp Reference

-Pr

to Pr

or Pr

to Pr

RO Num ND NC PT

Final Demand
Reference

-Pr

to Pr

or Pr

to Pr

RO Num ND NC PT FI

D.C. Bus Voltage

0 to 415 V or 0 to 830 V

RO Num ND NC PT FI

Output Frequency

± 550.00 Hz

RO Num ND NC PT FI

Output Voltage

0 to 325 V or 0 to 650 V

RO Num ND NC PT FI

Motor Rpm*****

33000.0 rpm

RO Num ND NC PT FI

Current Magnitude

0 to Drive Maximum Current A

RO Num ND NC PT FI

Torque Producing
Current

± Drive Maximum Current A

RO Num ND NC PT FI

Digital I/O Read
Word

0 to 2047

Bin

ND NC PT

Reference On

Off (0) or On (1)

Bit

ND NC PT

Reverse Select

Off (0) or On (1)

Bit

ND NC PT

Parameter

Range

(

)

Default

(

)

Type

RFC-A

Содержание Unidrive HS30



































































Результаты поиска

Содержание Unidrive HS30

Отзывы:

Похожие инструкции для Unidrive HS30

Бренды по названию

Популярные бренды

Control Techniques Unidrive HS30, Быстрый старт

Результаты поиска

Содержание Unidrive HS30

Отзывы:

Похожие инструкции для Unidrive HS30

Бренды по названию

Популярные бренды