Control Techniques Unidrive HS30 Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 66

background image

Unidrive M300/HS30 Quick Start Guide

43

Issue Number: 7

Defines the auto-tune test to be performed.
There are two autotune tests available in open loop mode, a stationary and a rotating test. A rotating
autotune should be used whenever possible so the measured value of power factor of the motor is
used by the drive.

Open Loop and RFC-A:

1. A stationary autotune can be used when the motor is loaded and it is not possible to remove the

load from the motor shaft. To perform a Stationary autotune, set Pr

38

to 1,

2. A rotating autotune should only be used if the motor is unloaded. A rotating autotune first

performs a stationary autotune, as above, then a rotating test is performed in which the motor is
accelerated with currently selected ramps up to a frequency of

Rated Frequency

(Pr

39

) x 2/3,

and the frequency is maintained at that level for 4 seconds. To perform a Rotating autotune, set
Pr

38

to 2.

RFC-A only:

3. This test measures the total inertia of the load and the motor. A series of progressively larger

torque levels are applied to the motor to accelerate the motor up to 3/4 x

Motor Rated Speed

(Pr

07

) to determine the inertia from the acceleration/deceleration time.

Following the completion of an autotune test the drive will go into the inhibit state. The drive must be
placed into a controlled disable condition before the drive can be made to run at the required
reference. The drive can be put in to a controlled disable condition by removing the Safe Torque Off
signal from terminals 31 & 34.

Enter the value from the rating plate of the motor. Defines the voltage to frequency ratio applied to
the motor.
* With the Unidrive HS30, the maximum is 3000.00 Hz.

38

Autotune

RW

Num

NC

US

OL

Ú

0 to 2

Ö

0

RFC-A

0 to 3

A rotating autotune will cause the motor to accelerate up to 2/3 base speed in the
direction selected regardless of the reference provided. Once complete the motor will
coast to a stop. The Safe Torque Off signals must be removed before the drive can be
made to run at the required reference.The drive can be stopped at any time by removing
the run signal or removing the drive enable.

39

Motor Rated Frequency

RW

Num

RA

US

OL

Ú

0.00 to 550.00 Hz*

Ö

Def.50: 50.00 Hz
Def.60: 60.00 Hz

RFC-A

WARNING

«
...
41
42
43
44
45
...
»

Содержание Unidrive HS30



































































Отзывы:

Нет отзывов

Похожие инструкции для Unidrive HS30

Бренд: BEIER-Electronic Страницы: 22

Бренд: Ohsung Electronics Страницы: 18

Бренд: Abicor Binzel Страницы: 8

Бренд: Wavelink Страницы: 69

Бренд: Dakota Digital Страницы: 6

CMD-2000 Series

Бренд: Dakota Digital Страницы: 10

Бренд: Z-Wave Страницы: 6

Бренд: Data I/O Страницы: 88

Бренд: Data Aire Страницы: 13

Бренд: Harmonic Drive Страницы: 25

Бренд: Nelson Страницы: 8

BT300 BurnerTronic

Бренд: Lamtec Страницы: 48

Бренд: Magellan Страницы: 2

Бренд: Patron Страницы: 17

Бренд: Ultraflex Страницы: 7

Frigolink FVB110B

Бренд: WURM Страницы: 4

Temp Alert TA2HL

Бренд: Winland Electronics Страницы: 2

Бренд: GE Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды