Control Techniques Unidrive HS30 Скачать руководство пользователя страница 36

Страница: 36 / 66

Unidrive M300/HS30 Quick Start Guide

Issue Number: 7

Defines the mode of analog input 1.

The table below gives all the possible analog input modes.

determines whether the reference is uni-polar or bi-polar.

See

Minimum Speed

(Pr

). Allows negative speed reference in keypad mode.

Analog Input 1 Mode

Txt

4-20.S (-6), 20-4.S (-5), 4-20.L (-4),

20-4.L (-3), 4-20.H (-2), 20-4.H (-1),

0-20 (0), 20-0 (1), 4-20.tr (2),

20-4.tr (3), 4-20 (4), 20-4 (5), Volt (6)

Volt (6)

Value

Text

Function

-6

4-20.S

Stop on loss

-5

20-4.S

Stop on loss

-4

4-20.L

4-20 mA switching to equivalent of 4 mA input current on loss

-3

20-4.L

20-4 mA switching to equivalent of 20 mA input current on loss

-2

4-20.H

4-20 mA hold at level before loss on loss

-1

20-4.H

20-4 mA hold at level before loss on loss

0-20

0-20 mA

20-0

20-0 mA

4-20.tr

4-20 mA trip on loss

20-4.tr

20-4 mA trip on loss

4-20

4-20 mA no action on loss

20-4

20-4 mA no action on loss

Volt

Voltage

In 4-20 mA and 20-4 mA modes loss of input is detected if the current falls below 3 mA.

If both analog inputs (A1 and A2) are to be set-up as voltage inputs, and if the
potentiometers are supplied from the drive's +10 V rail (terminal T4), they must have a
resistance >4 k

each.

Bipolar Reference Enable

Bit

Off (0) or On (1)

Off (0)

RFC-A

NOTE

Содержание Unidrive HS30



































































Результаты поиска

Содержание Unidrive HS30

Отзывы:

Похожие инструкции для Unidrive HS30

Бренды по названию

Популярные бренды

Control Techniques Unidrive HS30, Быстрый старт

Результаты поиска

Содержание Unidrive HS30

Отзывы:

Похожие инструкции для Unidrive HS30

Бренды по названию

Популярные бренды